0-1987995-1 데이터 시트보기 (PDF) - Tyco Electronics
부품명
상세내역
제조사
0-1987995-1 Datasheet PDF : 40 Pages
| |||
SOLARLOK Photovoltaic Interconnection System
Assembly and Installation Guidelines
Catalog 889753-3
Revised 9-2009
Table of Contents
Page
SOLARLOK Plug Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1. General Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2. Termination of the Cable Wires / Crimping of the Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3. Handling of the Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.1 Selection of Sealing Grommet for Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2 Connector Latching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.3 Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4. Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6. Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
SOLARLOK Plug Connector
Attention: This connector is to be used only to interconnect firmly fixed cables.
Do not disconnect under load.
Current path should only be disconnected using approved disconnect devices.
Cable assemblies shall be labeled with Part No. 1394470-1.
To protect against shock, ensure that conductors and their associated connectors
are separated from opposite polarity components.
IMPORTANT NOTE
Mounting and installation must be done by qualified and trained staff considering
all applying safety regulations. Tyco Electronics disclaims any warranty as a result of
non-compliance to these notes.
1. General Comments
Any kind of pollution (dust, oil, humidity, etc.) during the assembly process or to the unmated connector
can degrade contact and connector performance. This applies in particular to the seals and the crimping
of the contacts.
A clean assembly environment is therefore essential.
2. Termination of the
Cable Wires and Crimping
of the Contacts
SOLARLOK connectors use different crimp contacts for various wire gauges.
Possible wire gauges are 2.5 mm2, 4.0 mm2, 5.3 mm2 und 6.0 mm2 resp.
AWG 14, AWG 12 and AWG 10.
The tools to be used are selected based upon the wire gauge.
For the application specification, please refer to specification # 114-74013.
3.1 Handling of the Connectors
3.1 Selection of
3.1 Sealing Grommet
3.1 for Cable Connectors
Use only appropriate wire gauges.
Besides the standard seal/pinch ring combination further five different seals are available.
I 4.0 mm grommet inner diameter (for insulation diameter from 3.2 to 4.3 mm), Part No. 1394465-5
I 5.0 mm grommet inner diameter (for insulation diameter from 4.3 to 5.3 mm), Part No. 1394465-1
I 6.0 mm grommet inner diameter (for insulation diameter from 5.3 to 6.2 mm), Part No. 1394465-2
I 7.0 mm grommet inner diameter (for insulation diameter from 6.2 to 7.2 mm), Part No. 1394465-3
I 8.0 mm grommet inner diameter (for insulation diameter from 7.2 to 8.0 mm), Part No. 1394465-4
The grommet has to be matched with the outer diameter of the solar cable (see customer drawing,
Part No. 1394461 and Part No. 1394462) and the pinch ring (Part No. 1418677-2) must be applied.
All dimensions are in millimeters unless otherwise specified. All specifications subject to change.
29
Consult Tyco Electronics for latest specifications.
Share Link: 