ATMEGA168V-10AI 데이터 시트보기 (PDF) - Atmel Corporation
부품명
상세내역
제조사
ATMEGA168V-10AI Datasheet PDF : 349 Pages
| |||
minimum for the clock frequency used. See “Preventing EEPROM Corruption” on page
22 for details on how to avoid problems in these situations.
In order to prevent unintentional EEPROM writes, a specific write procedure must be fol-
lowed. Refer to the description of the EEPROM Control Register for details on this.
When the EEPROM is read, the CPU is halted for four clock cycles before the next
instruction is executed. When the EEPROM is written, the CPU is halted for two clock
cycles before the next instruction is executed.
The EEPROM Address
Register – EEARH and EEARL Bit
Read/Write
Initial Value
15
–
EEAR7
7
R
R/W
0
X
14
–
EEAR6
6
R
R/W
0
X
13
–
EEAR5
5
R
R/W
0
X
12
–
EEAR4
4
R
R/W
0
X
11
–
EEAR3
3
R
R/W
0
X
10
–
EEAR2
2
R
R/W
0
X
9
–
EEAR1
1
R
R/W
0
X
8
EEAR8
EEAR0
0
R/W
R/W
X
X
EEARH
EEARL
• Bits 15..9 – Res: Reserved Bits
These bits are reserved bits in the ATmega48/88/168 and will always read as zero.
• Bits 8..0 – EEAR8..0: EEPROM Address
The EEPROM Address Registers – EEARH and EEARL specify the EEPROM address
in the 256/512/512 bytes EEPROM space. The EEPROM data bytes are addressed lin-
early between 0 and 255/511/511. The initial value of EEAR is undefined. A proper
value must be written before the EEPROM may be accessed.
EEAR8 is an unused bit in ATmega48 and must always be written to zero.
The EEPROM Data Register –
EEDR
Bit
Read/Write
Initial Value
7
6
MSB
R/W
R/W
0
0
5
R/W
0
4
R/W
0
3
R/W
0
2
R/W
0
1
R/W
0
0
LSB
R/W
0
EEDR
• Bits 7..0 – EEDR7.0: EEPROM Data
For the EEPROM write operation, the EEDR Register contains the data to be written to
the EEPROM in the address given by the EEAR Register. For the EEPROM read oper-
ation, the EEDR contains the data read out from the EEPROM at the address given by
EEAR.
The EEPROM Control Register
– EECR
Bit
7
–
Read/Write
R
Initial Value
0
6
5
4
3
2
1
0
–
EEPM1 EEPM0 EERIE EEMPE EEPE EERE
EECR
R
R/W
R/W
R/W
R/W
R/W
R/W
0
X
X
0
0
X
0
• Bits 7..6 – Res: Reserved Bits
These bits are reserved bits in the ATmega48/88/168 and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM Programming Mode Bits
The EEPROM Programming mode bit setting defines which programming action that will
be triggered when writing EEPE. It is possible to program data in one atomic operation
(erase the old value and program the new value) or to split the Erase and Write opera-
18 ATmega48/88/168
2545D–AVR–07/04
Share Link: 