HT82K94A(2005) 데이터 시트보기 (PDF) - Holtek Semiconductor

부품명

상세내역

제조사

HT82K94A
(Rev.:2005)

USB Multimedia Keyboard Encoder 8-Bit MCU

Holtek Semiconductor 

HT82K94E/HT82K94A

There are some timing constrains and usages illustrated here. By setting the MISC register, MCU can perform reading,

writing and clearing actions. There are some examples shown in the following table for endpoint FIFO reading, writing

and clearing.

Actions

MISC Setting Flow and Status

Read FIFO0 sequence

00H®01H®delay 2ms, check 41H®read* from FIFO0 register and

check not ready (01H)®03H®02H

Write FIFO1 sequence

0AH®0BH®delay 2ms, check 4BH®write* to FIFO1 register and

check not ready (0BH)®09H®08H

Check whether FIFO0 can be read or not 00H®01H®delay 2ms, check 41H (ready) or 01H (not ready)®00H

Check whether FIFO1 can be written or not 0AH®0BH®delay 2ms, check 4BH (ready) or 0BH (not ready)®0AH

Read 0-sized packet sequence form FIFO0 00H®01H®delay 2ms, check 81H®read once (01H)®03H®02H

Write 0-sized packet sequence to FIFO1 0AH®0BH®delay 2ms, check 0BH®0FH®0DH®08H

Note: *: There are 2ms existing between 2 reading action or between 2 writing action

USB/PS2 Status and Control Register

The register is used to indicate there are USB suspend, USB resume and USB reset signal in USB bus. Also user can

output a high pulse in RMWK bit to wake-up the PC for USB remote function.

Bit No. Label R/W

Function

Read only, USB suspend indication. When this bit is set to ²1² (set by SIE), it indi-

0

SUSP R cates the USB bus enters suspend mode. The USB interrupt is also triggered on any

changes of this bit.

USB remote wake-up command. It is set by MCU to force the USB host leaving the

1

RMWK W suspend mode. When this bit is set to ²1², 2ms delay for clearing this bit to ²0² is

needed to insure the RMWK command is accepted by SIE.

USB reset indication. This bit is set/cleared by USB SIE. This bit is used to detect

2

URST R/W which bus (PS2 or USB) is attached. When the URST is set to ²1², this indicates that

a USB reset has occurred (the attached bus is USB) and a USB interrupt will be ini-

tialized.

USB resume indication. When the USB leaves the suspend mode, this bit is set to

²1² (set by SIE). This bit will appear 20ms waiting for the MCU to detect. When the

RESUME is set by the SIE, an interrupt will be generated to wake-up the MCU. In or-

3

RESUME R der to detect the suspend state, the MCU should set the USBCKEN and clear

SUSP2 (in SCC register) to enable the SIE detecting function. The RESUME will be

cleared while the SUSP is going ²0². When the MCU is detecting the SUSP, the RE-

SUME (wakes-up the MCU ) should be remembered and taken into consideration.

4

PS2DAI R Read only, USBD-/DATA input

5

PS2CKI R Read only, USBD+/CLK input

6

PS2DAO W Data for driving the USBD-/DATA pin (Default=²1²)

7

PS2CKO W Data for driving the USBD+/CLK pin (Default=²1²)

USC (1CH) Register

Rev. 1.00

21

November 22, 2005

Share Link: