LTC487CS 데이터 시트보기 (PDF) - Linear Technology
부품명
상세내역
제조사
LTC487CS Datasheet PDF : 8 Pages
| |||
LTC487
APPLICATI S I FOR ATIO
A TransZorb is a silicon transient voltage suppressor that
has exceptional surge handling capabilities, fast response
time, and low series resistance. They are available from
General Semiconductor Industries and come in a variety of
breakdown voltages and prices. Be sure to pick a break-
down voltage higher than the common-mode voltage
required for your application (typically 12V). Also, don’t
forget to check how much the added parasitic capacitance
will load down the bus.
DRIVER
Y
120Ω
Z
LTC487 • TA13
Figure 12. ESD Protection with TransZorbs
TYPICAL APPLICATI
RS232 to RS485 Level Translator with Hysteresis
R = 220k
RS232 IN
10k
5.6k
DRIVER
1/4 LTC487
Y
120Ω
Z
HYSTERESIS
=
10kΩ
•
—VY—-—VZ—
R
≈
19k
————
R
LTC487 • TA14
PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted.
N Package, 16-Lead Plastic DIP
0.300 – 0.325
(7.620 – 8.255)
0.130 ± 0.005
(3.302 ± 0.127)
0.045 – 0.065
(1.143 – 1.651)
0.009 – 0.015
(0.229 – 0.381)
0.015
(0.381)
MIN
+0.025
0.325 –0.015
( ) 8.255
+0.635
–0.381
0.125
(3.175)
MIN
0.045 ± 0.015
(1.143 ± 0.381)
0.100 ± 0.010
(2.540 ± 0.254)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTURSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm).
0.260 ± 0.010*
0.065 (6.604 ± 0.254)
(1.651)
TYP
0.018 ± 0.003
(0.457 ± 0.076)
0.770*
(19.558)
MAX
16 15 14 13 12 11 10 9
12 3 4 5 6 78
N16 0594
8
S Package, 16-Lead Plastic SOL
0.005
(0.127)
RAD MIN
0.291 – 0.299
(7.391 – 7.595)
(NOTE 2)
0.010
(0.254
–
–
0.029
0.737)
×
45°
0.093 – 0.104
(2.362 – 2.642)
0° – 8° TYP
0.037 – 0.045
(0.940 – 1.143)
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
NOTE:
NOTE 1
0.016 – 0.050
(0.406 – 1.270)
0.050
(1.270)
TYP
0.014 – 0.019
(0.356 – 0.482)
TYP
0.004 – 0.012
(0.102 – 0.305)
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS.
2. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
0.398 – 0.413
(10.109 – 10.490)
(NOTE 2)
16 15 14 13 12 11 10 9
123 45678
0.394 – 0.419
(10.007 – 10.643)
SOL16 0494
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
LT/GP 0894 0K REV A • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 1994
Share Link: 