M58LW032A 데이터 시트보기 (PDF) - STMicroelectronics

부품명

상세내역

제조사

M58LW032A

32 Mbit (2Mb x16, Uniform Block, Burst) 3V Supply Flash Memory

STMicroelectronics 

M58LW032A

failed. Depending on the cause of the failure other

Status Register bits may also be set to High, VOH.

s If only the Program Status bit (bit 4) is set High,

VOH, then the Program/Erase Controller has

applied the maximum number of pulses to the

byte and still failed to verify that the Write Buffer

has programmed correctly or that the Block is

protected.

s If the failure is due to a program or block protect

with VPP low, VOL, then VPP Status bit (bit 3) is

also set High, VOH.

s If the failure is due to a program on a protected

block then Block Protection Status bit (bit 1) is

also set High, VOH.

s If the failure is due to a program or erase

incorrect command sequence then Erase

Status bit (bit 5) is also set High, VOH.

Once set High, the Program Status bit can only be

reset Low by a Clear Status Register command or

a hardware reset. If set High it should be reset be-

fore a new Program or Erase command is issued,

otherwise the new command will appear to fail.

VPP Status (Bit 3). The VPP Status bit can be

used to identify if a Word Program, Erase, Block

Protection or Blocks Unprotection operation has

been attempted when VPP is Low, VIL. The VPP

Status bit cannot be used during a Write to Buffer

and Program operation.

When the VPP Status bit is Low, VOL, no Word Pro-

gram, Erase, Block Protection or Blocks Unprotec-

tion operations have been attempted with VPP

Low, VIL, since the last Clear Status Register com-

mand, or hardware reset. When the VPP Status bit

is High, VOH, a Word Program, Erase, Block Pro-

tection or Blocks Unprotection operation has been

attempted with VPP Low, VIL.

Once set High, the VPP Status bit can only be reset

by a Clear Status Register command or a hard-

ware reset. If set High it should be reset before a

new Program, Erase, Block Protection or Blocks

Unprotection command is issued, otherwise the

new command will appear to fail.

Program Suspend Status (Bit 2). The Program

Suspend Status bit indicates that a Program oper-

ation has been suspended and is waiting to be re-

sumed. The Program Suspend Status should only

be considered valid when the Program/Erase

Controller Status bit is High (Program/Erase Con-

troller inactive); after a Program/Erase Suspend

command is issued the memory may still complete

the operation rather than entering the Suspend

mode.

When the Program Suspend Status bit is Low,

VOL, the Program/Erase Controller is active or has

completed its operation; when the bit is High, VOH,

a Program/Erase Suspend command has been is-

sued and the memory is waiting for a Program/

Erase Resume command.

When a Program/Erase Resume command is is-

sued the Program Suspend Status bit returns Low.

Block Protection Status (Bit 1). The Block Pro-

tection Status bit can be used to identify if a Pro-

gram or Erase operation has tried to modify the

contents of a protected block.

When the Block Protection Status bit is Low, VOL,

no Program or Erase operations have been at-

tempted to protected blocks since the last Clear

Status Register command or hardware reset;

when the Block Protection Status bit is High, VOH,

a Program (Program Status bit 4 set High) or

Erase (Erase Status bit 5 set High) operation has

been attempted on a protected block.

Once set High, the Block Protection Status bit can

only be reset Low by a Clear Status Register com-

mand or a hardware reset. If set High it should be

reset before a new Program or Erase command is

issued, otherwise the new command will appear to

fail.

Reserved (Bit 0). Bit 0 of the Status Register is

reserved. Its value should be masked.

27/61

Share Link: