MBM29LV800BE70 데이터 시트보기 (PDF) - Fujitsu

부품명

상세내역

제조사

MBM29LV800BE70

FLASH MEMORY CMOS 8 M (1 M × 8/512 K × 16) BIT

Fujitsu 

MBM29LV800TE/BE60/70/90

Word 0 (A0 = VIL) represents the manufacturer’s code (Fujitsu = 04h) and (A0 = VIH) represents the device identifier

code (MBM29LV800TE = DAh and MBM29LV800BE = 5Bh for × 8 mode; MBM29LV800TE = 22DAh and

MBM29LV800BE = 225Bh for × 16 mode) . These two bytes/words are given in “MBM29LV800TE/BE Sector

Protection Verify Autoselect Codes” and “Expanded Autoselect Code Table” in “ DEVICE BUS OPERATION”.

All identifiers for manufactures and device will exhibit odd parity with DQ7 defined as the parity bit. In order to

read the proper device codes when executing the autoselect, A1 must be VIL. (See “MBM29LV800TE/BE Sector

Protection Verify Autoselect Codes” and “Expanded Autoselect Code Table” in “ DEVICE BUS OPERATION”.)

Write

Device erasure and programming are accomplished via the command register. The contents of the register serve

as inputs to the internal state machine. The state machine outputs dictate the function of the device.

The command register itself does not occupy any addressable memory location. The register is a latch used to

store the commands, along with the address and data information needed to execute the command. The

command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on

the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,

whichever happens first. Standard microprocessor write timings are used.

Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.

Sector Protection

The MBM29LV800TE/BE feature hardware sector protection. This feature will disable both program and erase

operations in any number of sectors (0 through 18) . The sector protection feature is enabled using programming

equipment at the user’s site. The devices are shipped with all sectors unprotected. Alternatively, Fujitsu may

program and protect sectors in the factory prior to shiping the device.

To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, (suggest

VID = 11.5 V) , CE = VIL, and A6 = VIL. The sector addresses (A18, A17, A16, A15, A14, A13, and A12) should be set to

the sector to be protected. “Sector Address Tables (MBM29LV800TE)” and “Sector Address Tables

(MBM29LV800BE) ” in “ FLEXIBLE SECTOR-ERASE ARCHITECTURE” define the sector address for each

of the nineteen (19) individual sectors. Programming of the protection circuitry begins on the falling edge of the

WE pulse and is terminated with the rising edge of the same. Sector addresses must be held constant during

the WE pulse. See “Sector Protection Timing Diagram” in “ TIMING DIAGRAM” and “Sector Protection Algo-

rithm” in “ FLOW CHART” for sector protection waveforms and algorithm.

To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9

with CE and OE at VIL and WE at VIH. Scanning the sector addresses (A18, A17, A16, A15, A14, A13, and A12) while

(A6, A1, A0) = (0, 1, 0) will produce a logical “1” code at device output DQ0 for a protected sector. Otherwise the

devices will read 00h for unprotected sector. In this mode, the lower order addresses, except for A0, A1, and A6

are DON’T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer and device codes.

A-1 requires to apply to VIL on byte mode.

It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing

a read operation at the address location XX02h, where the higher order addresses (A18, A17, A16, A15, A14, A13,

and A12) are the desired sector address will produce a logical “1” at DQ0 for a protected sector. See

“MBM29LV800TE/BE Sector Protection Verify Autoselect Codes” and “Expanded Autoselect Code Table” in

“ DEVICE BUS OPERATION” for Autoselect codes.

Temporary Sector Unprotection

This feature allows temporary unprotection of previously protected sectors of the MBM29LV800TE/BE devices

in order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage

(VID) . During this mode, formerly protected sectors can be programmed or erased by selecting the sector

addresses. Once the VID is taken away from the RESET pin, all the previously protected sectors will be protected

again. See “Temporary Sector Unprotection Timing Diagram” in “ TIMING DIAGRAM” and “Temporary Sector

Unprotection Algorithm” in “ FLOW CHART”.

17

Share Link: