IDT49C466PQF 데이터 시트보기 (PDF) - Integrated Device Technology
부품명
상세내역
제조사
IDT49C466PQF Datasheet PDF : 27 Pages
| |||
IDT49C466/A Flow-thruEDC™
ERROR DETECTION AND CORRECTION UNIT
COMMERCIAL TEMPERATURE RANGES
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
Com’l.
Unit
VCC
Power Supply Voltage
–0.5 to +7.0 V
VTERM
Terminal Voltage with
Respect to Ground
–0.5 to
V
VCC + 0.5
TBIAS
TSTG
Temperature Under Bias
Storage Temperature
–55 to +125 °C
–55 to +125 °C
IOUT
DC Output Current
30
mA
NOTE:
2617 tbl 09
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress
rating only, and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to Absolute Maximum Ratings for
extended periods of time may affect reliability.
CAPACITANCE (TA = +25°C, f = 1.0 MHz)
Symbol Parameter(1)
Conditions
Typ. Unit
CIN
Input
VIN = 0V PQFP
5
pF
Capacitance
COUT Output
VOUT = 0V PQFP
7
pF
Capacitance
NOTE:
1. This parameter is sampled and not 100% tested.
2617 tbl 10
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
The following conditions apply unless otherwise specified:
Commercial: TA = 0°C to +70°C, VCC = 5.0V ± 5%
Symbol
Parameter
Test Conditions(1)
Min. Typ.(2)
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2.0
—
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
—
IIH
Input HIGH Current
VCC = Max., VIN = 2.7V
—
0.1
IIL
Input LOW Current
VCC = Max., VIN = 0.5V
—
-0.1
IOZ
Off State (Hi-Z)
VCC = Max.
VO = 0V
—
-0.1
Output Current
IOS
Short Circuit Current
VCC = Max.(3), VOUT= 0V
VO = 3V
—
0.1
–20
—
VOH
Output HIGH Voltage
VCC = Min.,
IOH = –2mA
2.4
3.6
VIN = VIH or VIL
VOL
Output LOW Voltage
VCC = Min.
IOL = 8mA
—
0.3
VIN = VIH or VIL
VH
Input Hysteresis on input control lines
—
200
NOTES:
1. For conditions shown as min. or max., use appropriate Vcc value.
2. Typical values are at VCC = 5.0V, +25°C ambient temperature.
3. Not more than one output should be shorted at a time. Duration of the short circuit test should not exceed one second.
Max.
—
0.8
5.0
–5.0
–10
10
–150
—
0.5
—
Unit
V
V
µA
µA
µA
mA
V
V
mV
2617 tbl 11
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (Con't)
The following conditions apply unless otherwise specified:
Commercial: TA = 0°C to +70°C, VCC = 5.0V ± 5%
Symbol
Parameter
Test Conditions(1)
Min.
ICCQC Quiescent Power Supply Current VIN = VCC, or VIN = GND
—
VCC = Max.
ICCQT Quiescent Power Supply Current VIN = 3.4V
—
TTL Input Levels
VCC = Max.
ICCD
Dynamic Power Supply Current VIN = VCC, or VIN = GND
—
VCC = Max. f = 10MHz Correct Mode
NOTES:
1. For conditions shown as Min. or Max., use appropriate Vcc value.
2. Typical values are at VCC = 5.0V, +25°C ambient temperature.
Typ.(2)
3.0
0.3
—
Max.
15
1
100
Unit
mA
mA/
Input
mA
2617 tbl 12
11.7
12
Share Link: 