87C196CB(1998) 데이터 시트보기 (PDF) - Intel

부품명

상세내역

제조사

87C196CB
(Rev.:1998)

ADVANCED 16-BIT CHMOS MICROCONTROLLER WITH INTEGRATED CAN 2.0

Intel 

87C196CA/87C196CB - Express

5.0

ELECTRICAL CHARACTERISTICS

ABSOLUTE MAXIMUM RATINGS*

Storage Temperature

–60°C to +150°C

Voltage from VPP or EA# to

VSS or ANGND................................ –0.5 V to +13.0 V

Voltage from any other pin to

VSS or ANGND................................ –0.5 V to +7.0 V

This includes VPP on ROM and CPU devices.

Power Dissipation ................................. 0.5 W

OPERATING CONDITIONS

NOTICE: This is a production data sheet. The specifi-

cations are subject to change without notice. Verify with

your local Intel sales office that you have the latest

datasheet before finalizing a design.

*WARNING: Stressing the device beyond the

“Absolute Maximum Ratings” may cause

permanent damage. These are stress ratings

only. Operation beyond the “Operating

Conditions” is not recommended and extended

exposure beyond the “Operating Conditions”

may affect device reliability.

TA (Ambient Temperature Under Bias).....–40°C to +85°C

VCC (Digital Supply Voltage)

4.5 V to 5.5 V

VREF (Analog Supply Voltage)

4.5 V to 5.5 V

FOSC (Oscillator Frequency) .................... 4 MHz to 16 MHz

NOTE: ANGND and VSS should be nominally at the same

potential.

5.1

DC CHARACTERISTICS

Table 5. DC Characteristics (Under Listed Operating Conditions) (Sheet 1 of 2)

Symbol

Parameter

Min

Typ

Max Units

Test

Conditions

VCC Supply Current

(–40°C to +85°C Ambient)

ICC

CA

CB

XTAL1 = 16 MHz

90

mA VCC = VPP = VREF= 5.5 V

100

(While Device in Reset)

IREF

A/D Reference Supply

Current

5

mA

IIDLE

Idle Mode Current

CA

CB

XTAL1 = 16 MHz

40

35

mA

VCC = VPP = VREF = 5.5 V

IPD

Powerdown Mode Current

50

TBD

µA VCC = VPP = VREF = 5.5 V

(Notes 6,9)

VIL

Input Low Voltage (All Pins) –0.5

0.3 VCC

V For PORT0 (Note 8)

VIH

Input High Voltage

0.7 VCC

VCC + 0.5 V For PORT0 (Note 8)

NOTES:

1. All BD (bidirectional) pins except INST and CLKOUT. INST and CLKOUT are excluded due to not being

weakly pulled high in reset. BD pins include Port1, Port2, Port3, Port4, Port5 and Port6 except SPLINT

(P5.4) and HLDA (P2.6).

2. Standard Input pins include XTAL1, EA#, RESET and Port 1/2/5/6 when setup as inputs.

3. All Bidirectional I/O pins when configured as Outputs (Push/Pull).

4. Device is Static and should operate below 1 Hz, but only tested down to 4 MHz.

5. Maximum IOL /IOH currents per pin are characterized and published at a later date.

6. Typicals are based on limited number of samples and are not guaranteed. The values listed are at room

temperature and VREF = VCC = 5 V.

7. Violating these specifications in reset may cause the device to enter test mode (P5.4 and P2.6).

8. When P0 is used as analog inputs, refer to A/D specifications for this characteristic.

9. For temperatures < 100°C typical is 10 µA.

ADVANCE INFORMATION Datasheet

11

Share Link: