STK433-890N-E 데이터 시트보기 (PDF) - SANYO -> Panasonic
부품명
상세내역
제조사
STK433-890N-E Datasheet PDF : 11 Pages
| |||
STK433-060N-E
Specifications
Absolute Maximum Ratings at Ta = 25°C, Tc = 25°C unless otherwise specified
Parameter
Symbol
Conditions
Maximum power supply voltage
Minimum operation supply voltage
#13 Operating voltage
*5
VCC max (0)
VCC max (1)
VCC max (2)
VCC min
VST OFF max
Non- signal
Signal, RL ≥ 6Ω
Signal, RL ≥ 4Ω
#13 voltage
Thermal resistance
θj-c
Per one power transistor
Junction temperature
Tj max
Should satisfy Tj max and Tc max
Operating substrate temperature
Tc max
Storage temperature
Tstg
Allowable time for load short-circuit
ts
*4
VCC = ±27V, RL = 6Ω, f = 50Hz
PO = 35W, 1ch drive
Ratings
±46
±40
±33
±10
-0.3 to +5.5
3.5
150
125
-30 to +125
0.3
Unit
V
V
V
V
V
°C/W
°C
°C
°C
s
Operating Characteristics at Tc = 25°C, RL = 6Ω (Non-inductive Load), Rg = 600Ω, VG = 30dB
Conditions *2
Ratings
Parameter
Symbol
VCC
f
PO
THD
[V]
[Hz]
[W]
[%]
min
typ
Output power
*1 PO 1
±27
20 to 20k
0.4
33
35
PO 2
±27
1k
10
50
PO 3
±22
1k
1
RL=4Ω
35
Total harmonic distortion *1 THD 1
±27
20 to 20k
5.0
VG=30dB
THD 2
±27
1k
0.02
Frequency characteristics *1 fL, fH
±27
1.0
Input impedance
ri
±27
1k
1.0
+0 -3dB
20 to 50k
55
Output noise voltage
*3 VNO
±33
Quiescent current
ICCO
±33
Quiescent current at stand-by
ICST
±33
Output neutral voltage
VN
±33
#13 Stand-by ON threshold *5 VST ON
±27
Rg=2.2kΩ
No load
15
30
VST=0V
-70
0
Stand-by
0
#13 Stand-by OFF threshold *5 VST OFF
±27
Operation
2.5
3.0
max
0.4
1.0
70
1.0
+70
0.6
5.5
Unit
W
%
Hz
kΩ
mVrms
mA
mA
mV
V
V
Note
*1. 1channel operation.
*2. All tests are measured using a constant-voltage supply unless otherwise specified
*3. The output noise voltage is peak value of an average-reading meter with a rms value scale (VTVM).
A regulated AC supply (50Hz) should be used to eliminate the effects of AC primary line flicker noise
*4. Allowable time for load short-circuit and output noise voltage are measured using the specified transformer power
supply.
*5. The impression voltage of ‘#13 (Stand-By) pin’ must not exceed the maximum rating.
Power amplifier operate by impressing voltage +2.5 to +5.5V to ‘#13 (Stand-By) pin’.
* Please connect - PreVCC pin (#1 pin) with the stable minimum voltage.
and connect so that current does not flow in by reverse bias.
* In case of heat sink design, we request customer to design in the condition to have assumed market.
* The case of this Hybrid-IC is using thermosetting silicon adhesive (TSE322SX).
* Weight of HIC : (typ) 12.0g
Outer carton dimensions (W×L×H) : 452mm×325mm×192mm
Specified transformer power supply
(Equivalent to MG-200)
DBA40C
10000μF
+VCC
+
500Ω
+
500Ω
10000μF
-VCC
No.A2106-2/11
Share Link: 