LH1522 데이터 시트보기 (PDF) - Vishay Siliconix
부품명
상세내역
제조사
LH1522 Datasheet PDF : 7 Pages
| |||
www.vishay.com
LH1522AB, LH1522AAC, LH1522AACTR
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
INPUT
LED continuous forward current
LED reverse voltage
OUTPUT
IR 10 μA
IF
50
mA
VR
8
V
DC or peak AC load voltage
Continuous DC load current,
one pole operating
IL 50 μA
VL
200
V
IL
200
mA
Continuous DC load current,
two poles operating
IL
140
mA
Peak load current (single shot)
SSR
t = 100 ms
IP
(2)
Ambient temperature range
Storage temperature range
Pin soldering temperature (3)
Input to output isolation test voltage
Pole-to-pole isolation voltage (S1 to S2) (1),
(dry air, dust free, at sea level)
t = 10 s max.
t = 1 s, IISO = 10 μA max.
Tamb
Tstg
Tsld
VISO
- 40 to + 85
- 40 to + 150
260
5300
1600
°C
°C
°C
VRMS
V
Output power dissipation (continuous)
Pdiss
600
mW
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1) Breakdown occurs between the output pins external to the package.
(2) Refer to current limit performance application note 58 for a discussion on relay operation during transient currents.
(3) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
UNIT
INPUT
LED forward current, switch turn-on
LED forward current, switch turn-off
LED forward voltage
OUTPUT
IL = 100 mA, t = 10 ms
VL = ± 150 V
IF = 10 mA
IFon
1
2
mA
IFoff
0.2
1.1
mA
VF
1.15
1.26
1.45
V
On-resistance
IF = 5 mA, IL = 50 mA
RON
6
10
15
Off-resistance
IF = 0 mA, VL = ± 100 V
ROFF
0.5
5000
G
Current limit
IF = 5 mA, t = 5 ms, VL = ± 5 V
ILMT
300
360
460
mA
Off-state leakage current
IF = 0 mA, VL = ± 100 V
IO
IF = 0 mA, VL = ± 200 V
IO
0.02
200
nA
1
μA
Output capacitance
IF = 0 mA, VL = 1 V
CO
60
pF
IF = 0 mA, VL = 50 V
CO
15
pF
Pole-to-pole capacitance (S1 to S2)
IF = 5 mA
0.5
pF
Switch offset
IF = 5 mA
VOS
0.15
μV
TRANSFER
Capacitance (input to output)
VISO = 1 V
CIO
1.1
pF
Note
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
Turn-on time
Turn-off time
IF = 10 mA, IL = 50 mA
ton
IF = 10 mA, IL = 50 mA
toff
TYP.
1
0.7
MAX.
2
2
UNIT
ms
ms
Rev. 1.7, 25-Jul-11
2
Document Number: 83821
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 