MBM29F800BA-70 데이터 시트보기 (PDF) - Spansion Inc.

부품명

상세내역

제조사

MBM29F800BA-70

FLASH MEMORY

Spansion Inc. 

MBM29F800TA-55/-70/-90/MBM29F800BA-55/-70/-90

Write

Device erasure and programming are accomplished via the command register. The contents of the register serve

as inputs to the internal state machine. The state machine outputs dictate the function of the device.

The command register itself does not occupy any addressable memory location. The register is a latch used to

store the commands, along with the address and data information needed to execute the command. The

command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on

the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,

whichever happens first. Standard microprocessor write timings are used.

Refer to “s AC CHARACTERISTICDS” and “s TIMING DIAGRAM” for specific timing parameters.

Sector Protection

The MBM29F800TA/BA features hardware sector protection. This feature will disable both program and erase

operations in any number of sectors (0 through 18). The sector protection feature is enabled using programming

equipment at the user’s site. The device is shipped with all sectors unprotected.

To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, (suggest

VID = 11.5V), CE = VIL, and A6 = VIL. The sector addresses (A18, A17, A16, A15, A14, A13, and A12) should be set to

the sector to be protected. “Sector Address Tables (MBM29F800TA)” and “Sector Address Tables

(MBM29F800BA)” in s FLEXIBLE SECTOR ERASE ARCHITECTURE define the sector address for each of

the nineteen (19) individual sectors. Programming of the protection circuitry begins on the falling edge of the

WE pulse and is terminated with the rising edge of the same. Sector addresses must be held constant during

the WE pulse. See “Sector Protection Timing Diagram” in s TIMING DIAGRAM and “Sector Protection Algorithm”

in s FLOW CHART for sector protection waveforms and algorithm.

To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9

with CE and OE at VIL and WE at VIH. Scanning the sector addresses (A18, A17, A16, A15, A14, A13, and A12) while

(A6, A1, A0) = (0, 1, 0) will produce a logical “1” code at device output DQ0 for a protected sector. Otherwise the

devices will read 00h for unprotected sector. In this mode, the lower order addresses, except for A0, A1, and A6

are DON’T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer and device codes.

A-1 requires to apply to VIL on byte mode.

It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing

a read operation at the address location XX02h, where the higher order addresses (A18, A17, A16, A15, A14, A13,

and A12) are the desired sector address will produce a logical “1” at DQ0 for a protected sector. See

“MBM29F800TA/BA Sector Protection Verify Autoselect Codes” and “Expanded Autoselect Code Table” in

s DEVICE BUS OPERATION for Autoselect codes.

Temporary Sector Unprotection

This feature allows temporary unprotection of previously protected sectors of the MBM29F800TA/BA device in

order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage

(12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector

addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected

again. Refer to “Temporary Sector Unprotection Timing Diagram” in s TIMING DIAGRAM and “Temporary Sector

Unprotection Algorithm” in s FLOW CHART.

14

Share Link: