HA-5177/883 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
HA-5177/883 Datasheet PDF : 5 Pages
| |||
HA-5177/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AV = +1V/V, Unless Otherwise Specified.
LIMITS
PARAMETERS
Average Offset Voltage
Drift
Average Offset Current
Drift
Average Bias Current Drift
Differential Input
Resistance
Low Frequency
Peak-to-Peak Noise Voltage
Low Frequency
Peak-to-Peak Noise Current
Input Noise Voltage
Density
Input Noise Current
Density
Gain Bandwidth Product
Full Power Bandwidth
Minimum Closed Loop
Stable Gain
Settling Time
Output Resistance
Power Consumption
SYMBOL
VIOTC
IIOTC
IRTC
RIN
ENP-P
INP-P
EN
IN
GBWP
FPBW
CLSG
tS
ROUT
PC
CONDITIONS
VCM = 0V
Versus Temperature
Versus Temperature
VCM = 0V
0.1Hz to 10Hz
0.1Hz to 10Hz
RS = 20Ω, fO = 10Hz
RS = 20Ω, fO = 100Hz
RS = 20Ω, fO = 1kHz
RS = 2MΩ, fO = 10Hz
RS = 2MΩ, fO = 100Hz
RS = 2MΩ, fO = 1kHz
VO = 100mV,
1Hz ≤ fO ≤ 100kHz
VPEAK = 10V
RL = 2kΩ, CL = 50pF
To 0.1% for a 10V Step
Open Loop
VOUT = 0V, IOUT =
0mA
NOTES
1
1
1
1
1
1
1
1
1
1
1
1
1
1, 2
1
1
1
1, 3
TEMPERATURE MIN
-55oC to +125oC
-
-55oC to +125oC
-
-55oC to +125oC
-
+25oC
20
+25oC
-
+25oC
-
+25oC
-
+25oC
-
+25oC
-
+25oC
-
+25oC
-
+25oC
-
+25oC
2
+25oC
8
-55oC to +125oC
+1
+25oC
-
+25oC
-
-55oC to +125oC
-
MAX
0.6
40
40
-
UNITS
µV/oC
pA/oC
pA/oC
MΩ
0.6
µVP-P
45
pAP-P
18
nV/√Hz
13
nV/√Hz
11
nV/√Hz
4
pA/√Hz
2.3 pA/√Hz
1
pA/√Hz
-
MHz
-
kHz
-
V/V
15
µs
70
Ω
51
mW
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These param-
eters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
3. Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.)
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUPS (SEE TABLES 1 AND 2)
Interim Electrical Parameters (Pre Burn-In)
1
Final Electrical Test Parameters
1 (Note 1), 2, 3, 4, 5, 6, 7
Group A Test Requirements
1, 2, 3, 4, 5, 6, 7
Groups C and D Endpoints
1
NOTE:
1. PDA applies to Subgroup 1 only.
Spec Number 511041-883
4
Share Link: 