DND9000 데이터 시트보기 (PDF) - Unspecified

부품명

상세내역

제조사

DND9000

DOUBLE CD PLAYER

Unspecified 

ENGLISH

5 BASIC OPERATION

Play and Pause

• Each push of the !4 PLAY/PAUSE button switches

between playback and pause. PLAY/PAUSE button

illuminates solid green during playback and flashed

in pause.

• When the !4 PLAY/PAUSE button is pushed during

play, the DN-D9000 pauses playback at that point.

Push !4 PLAY/PAUSE button once again and

playback resumes.

Adjusting the Pitch

• With Pitch slider you can adjust the playback speed

(Pitch).

• If you would not change key of sound, use the Key

Adjust function.

PITCH/KEY

1 Push the @9 PITCH/KEY button

to PITCH LED lights up.

RANGE

Play and Cue

• When the !5 CUE button is pushed during playback,

the track stops and returns to the position that

current playback started (Cue point) and prepares

for next playback. This function is called Back-Cue.

With Back-Cue function, you can start from exactly

same position. The CUE button illuminates solid red

when DN-D9000 is ready to start playback.

• You can set and change Cue point as follows.

• When you started playback.

• Track select finished.

• Manual Search.

Move the Cue Point

• If you would not like to start playback from

beginning of the track, you need to move Cue Point

using Manual Search function.

Push the @6 BEND/SEARCH

1

button to set Jog Wheel to

search mode. The SEARCH LED

will flash.

S

Turn the @2 Jog Wheel to

2

change Cue point. You can hear

the short sound of the current

Cue point.

After you found your

3

preferred Cue point, push

the !5 CUE button then new

Cue point is set.

CUE

STUTTER

The Manual Search speed

4

changes according to the speed

at which the @2 Jog Wheel is

turned.

Pitch decreases

Move the @8 Pitch slider to

2

adjust the pitch. The current

0%

pitch setting is displayed on the

display.

Pitch increases

DN-D9000 has five pitch ranges, PITCH/KEY

4%, 10%, 16%, 24% and 100%.

3

When the @9 RANGE button

is pushed for more than 1 sec,

RANGE

the pitch range can be selected

with the PARAMETERS knob.

Pitch Bend

• With PITCH BEND function you can change pitch

temporary. DN-D9000 has two ways for this

function PITCH BEND buttons and Jog Wheel.

[PITCH BEND +/- buttons]

• Push the #0 PITCH BEND

PITCH BEND

– or #1 + button for

momentary change of

1 pitch.

While holding these buttons down, the pitch

continues to change up to the limitation.

• After releasing the PITCH BEND buttons,

playback pitch returns to slider setting.

[Jog Wheel]

• In Play mode, the BEND LED starts flashing.

• The pitch increases gradually

when the @2 Jog Wheel is

2 turned clockwise and

decreases when turned

counterclockwise.

• When you stop turning the Jog Wheel, the

playing speed returns to the previous pitch.

6 SCRATCH

You can scratch in CD or sampler mode. Also you can select the scratch sound direction to (turn direction of Jog

Wheel), both, forward and reverse. These selections give you variety of scratch effects.

q, e, r

-TRACK HOT START

RVS

SAMP1

SAMP2 SAMPLER B

FLIP

A3

A4

B

CLR

A3 A4 CUE

FLIP

A1

A2

B

CLR

A1 A2

EXIT/RELOOP

EXIT/

RELOOP

EXIT/

RELOOP

4 HOT START

A3 B

A1 B

MEMO

PROG

A4 B

A2 B

TOTAL REMAIN ELAPSED CONT. SINGLE

m

s

m

s

f

KEY ADJ.

DRAG S.

BRAKE

ECHO

DUMP

RVS

  -TRACK PLAY

STOP

CUE

PARAMETERS

PUSH

ON/OFF

A 3/4

A/B TRIM

PITCH/VOL

SPLICE

SCRATCH

SELECT

DIR

SOURCE FX

CONT./SINGLE

TIME

MEMO PROGRAM PLATTER MODE

TRACK

OPEN/

CLOSE

PITCH/KEY PITCH BEND

RANGE

0%

RELAY TOTAL TIME PRESET RANDOM

ALL OFF

-TRACK HOT START

RVS

SAMP1

SAMP2 SAMPLER B

FLIP

A3

A4

B

CLR

A3 A4 CUE

FLIP

A1

A2

B

CLR

A1 A2

EXIT/RELOOP

EXIT/

RELOOP

STOP

CUE

-TRA

A 3/4

A/B T

EXIT/

RELOOP

4 HOT START PITCH/VOL

SPL

A3 B

A1 B

MEMO

PROG

A4 B

A2 B

TOTAL REMAIN ELAPSED CONT. SINGLE

m

s

m

s

f

KEY ADJ.

DRAG S.

BRAKE

ECHO

DUMP

RVS

CONT./SINGLE

TIME

MEMO PROGRAM PLATTER MODE

RELAY TOTAL TIME PRESET RANDOM

ALL OFF

CUE

STUTTER

PLAY/PAUSE

TAP

AUTO

w

BEND

S

REMOTE CONTROLLER RC-D90

CUE

STUTTER

PLAY/PAUSE

TAP

AUTO

SCRATCH PLAY

q Push the SCRATCH button to

enter Scratch mode,

SCRATCH LED flash.

SCRATCH

DIR

w Turn the Jog Wheel to start

1

scratching a specified point.

e To exit Scratch mode, push

the SCRATCH button once

again.

SCRATCH

DIR

Select SCRATCH source and direction

r After the DIR button

pushed for more than 1 sec,

2-1 combinations of scratch

source and direction can be

selected with the

PARAMETERS knob.

SCRATCH

DIR

• DN-D9000 displays current setting as

follows.

DISC/BOTH: (default)

Scratch Main with track both direction.

DISC/FWD:

Scratch Main track with forward direction.

DISC/RVS:

Scratch Main track only reverse direction.

2-2 SAMP/BOTH:

Scratch Sampler sound with both direction.

SAMP/FWD:

Scratch Sampler sound with forward only.

SAMP/RVS:

Scratch Sampler sound with reverse only.

To use SAMP/BOTH, FWD, RVS scratch,

Sampler setting is needed.

11

Share Link: