ATC113 데이터 시트보기 (PDF) - Unspecified

부품명

상세내역

제조사

ATC113

ATC Millimeter Wavelength Single Layer Capacitors

Unspecified 

ATC Single Layer Millimeter Wavelength Microcaps®: 111 & 116 Series

ATC PART NUMBER CODE

111 S CA 0R5 B 100 T T

Series:

111 Beveled edges

116 Perpendicular edges

Case Size: See Mechanical

Configurations; page 5.

Dielectric Style:

Max. 2 characters, see Specification

Chart; page 3.

Capacitance Code: 2 significant digits,

R = Decimal point; Number of zeros following

significant digits. See pages 6 and 7 for

capacitance values.

Termination Suffix

Code

Description

TT

(Standard)

Thin Film:

Titanium Tungsten / Nickel /Gold

100 µ in. min. Gold

AP

Thick Film: Platinum Gold

300 µ in. min.

WVDC (in Volts): 3 significant digits,

100 Volts is standard.

Capacitance Tolerance

Code A (pF) B (pF) C (pF) D (pF) F (%) G (%) J (%) K (%) M (%)

Tol. ± 0.05 ± 0.1 ± 0.25 ± 0.5 ± 1 ± 2% ± 5 ± 10 ±20%

Use the Standard Capacitance Value chart on pages 6 and 7 to select a code which is within the capacity range given for a

specific case size/dielectric combination.

Select a capacitance tolerance from the available tolerances listed in the Selection Chart.

The above part number describes a 100 volt, T T termination (thin film), 111 series (beveled edge) capacitor, case size S (0.018"

square nominal), CA dielectric (0 ±30 ppm/°C). This size/dielectric combination has a capacitance range of 0.4 to 0.9 pF and

available tolerances of B, C or D. 0R5 defines a capacitance value of 0.5 pF. B tolerance (±0.1 pF) was selected.

ATC accepts orders for our parts using designations with or without the “ATC” prefix. Both methods of defining the part number are equivalent, i.e., part

numbers referenced with the “ATC” prefix are interchangeable to parts referenced without the “ATC” prefix. Customers are free to use either in specifying or

procuring parts from American Technical Ceramics.

Design Your Own Single Layer Capacitor

ATC gives you the ability to create custom values and dimensions. When circuit board area is tight or you need to match your

stripline width, you can optimize the size and shape of required SLCs. This same technique can be used to build special values

that fall outside of the standard offerings.

Custom Values and Sizes

Optimize the best combination of length, width, thickness and dielectric material for your circuit/stripline capacitor requirements.

L = Length

10 to 100 mils

ATC

SLC

T = Thickness

4 to 12 mils

Design Guidelines

C = Capacitance (pF)

L = Length

W = Width

T = Thickness

W = Width

10 to 100 mils

C = (.225 K x L x W) / (1000 T)

A

AX

10 to 100 mils, may not exceed 20 x T or 2.5 x W

BA

10 to 100 mils, may not exceed 20 x T

BB

4 to 12 mils, less than or equal to L/2 or W/2

CA

Dielectric Constant (K)

14 CC 130 EC

650

23 DA 165 J

1100

36 DB 200 F

2000

31 HC 350 G

4500

62

EA 650

K

9000

4

American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142

phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales@atceramics.com • http://www.atceramics.com

Share Link: