MAX3657(2004) 데이터 시트보기 (PDF) - Maxim Integrated
부품명
상세내역
제조사
MAX3657 Datasheet PDF : 15 Pages
| |||
155Mbps Low-Noise Transimpedance
Amplifier
ABSOLUTE MAXIMUM RATINGS
Power-Supply Voltage ...........................................-0.5V to +6.0V
Input Continuous Current ................................................±3.5mA
Voltage at OUT+, OUT- ...................(VCC - 1.5V) to (VCC + 0.5V)
Voltage at FILT, MON .................................-0.5V to (VCC + 0.5V)
Continuous Power Dissipation
12-Pin QFN (derate 14.7mW/°C above +70°C) .........1176mW
Operating Temperature Range
12-Pin QFN ......................................................-40°C to +85°C
Operating Junction Temperature Range
Die .................................................................-40°C to +150°C
Storage Temperature Range .............................-55°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Die Attach Temperature...................................................+400°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC1 = +2.97V to +3.63V, 200Ω load between OUT+ and OUT-, TA = -40°C to +85°C. Typical values are at VCC = +3.3V, TA = +25°C,
unless otherwise noted.) (Note 1)
PARAMETER
Supply Current
Input Bias Voltage
Transimpedance Linear Range
Small-Signal Transimpedance
SYMBOL
ICC
VIN
Z21
CONDITIONS
IIN ≤ 1mA
0.95 < linearity < 1.05, referred to gain at
1µAP-P input
Differential output, IIN < 200nAP-P
Output Common-Mode Voltage
AC-coupled outputs
Output Resistance (Per Side)
Maximum Differential Output Voltage
Filter Resistor
DC Input Overload
Monitor Nominal Gain
Monitor Gain Stability
(Note 3)
ROUT
VOUT(max)
RFILT
Single-ended output resistance
IIN = 2mAP-P, VOUT = (VOUT+) - (VOUT-)
GNOM
∆G
VCC = +3.3V, +25°C (Note 2)
IIN = 100µA to 1mA
IIN = 5µA
Die
QFN package
IIN = 2µA
Die only
IIN = 1µA
Die only
MIN TYP MAX UNITS
23
34
mA
1
1.3
V
2
µAP-P
44
54
65
kΩ
VCC -
V
0.225
82
100 118
Ω
170 250 450 mVP-P
640 800 960
Ω
1
1.5
mA
0.8
1
1.2
A/A
-1.5
+1.5
-1.5
+2.2
-3.0
+2.7 dB
-4.0
+3.4
±2.0
AC ELECTRICAL CHARACTERISTICS
(VCC = +2.97V to +3.63V, 200Ω load between OUT+ and OUT-, CIN = 0.5pF, CFILT = 400pF, CVCC2 = 680pF, TA = -40°C to +85°C.
Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Small-Signal Bandwidth
Low-Frequency Cutoff
AC Overload
Pulse-Width Distortion
Input-Referred Noise Current
RMS Noise Density
Monitor Bandwidth
BW-3dB Relative to gain at 1MHz
-3dB, IIN = 1µA
PWD
In
300nAP-P ≤ IIN ≤ 2mAP-P
f = 100MHz (Note 4)
f = 117MHz
f = 100MHz
IIN = 1µA
110
5
2
22
14
1.3
5
MHz
25
kHz
mAP-P
psP-P
15
nARMS
pA/√Hz
kHz
2 _______________________________________________________________________________________
Share Link: 