OR4E10 데이터 시트보기 (PDF) - Agere -> LSI Corporation

부품명

상세내역

제조사

OR4E10

ORCA® Series 4 Field-Programmable Gate Arrays

Agere -> LSI Corporation 

ORCA Series 4 FPGAs

Preliminary Data Sheet

December 2000

Programmable Logic Cells (continued)

The PFU is organized in a twin-quad fashion: two sets

of four LUTs and FFs that can be controlled indepen-

dently. Each PFU has two independent programmable

clocks, clock enables, local set/reset, and data selects

with one available per set of quad FFs.

LUTs may also be combined for use in arithmetic func-

tions using fast-carry chain logic in either 4-bit or 8-bit

modes. The carry-out of either mode may be registered

in the ninth FF for pipelining. Each PFU may also be

configured as a synchronous 32 x 4 single- or dual-port

RAM or ROM. The FFs (or latches) may obtain input

from LUT outputs or directly from invertible PFU inputs,

or they can be tied high or tied low. The FFs also have

programmable clock polarity, clock enables, and local

set/reset.

The LUTs can be programmed to operate in one of

three modes: combinatorial, ripple, or memory. In com-

binatorial mode, the LUTs can realize any 4-, 5-, or

6-input logic function and many multilevel logic func-

tions using ORCA’s SWL connections. In ripple mode,

the high-speed carry logic is used for arithmetic func-

tions, comparator functions, or enhanced data path

functions. In memory mode, the LUTs can be used as a

32 x 4 synchronous RAM or ROM, in either single- or

dual-port mode.

The SLIC is connected from PLC routing resources

and from the outputs of the PFU. It contains eight

3-state, bidirectional buffers and logic to perform up to

a 10-bit AND function for decoding, or an AND-OR with

optional INVERT to perform PAL-like functions. The

3-state drivers in the SLIC and their direct connections

from the PFU outputs make fast, true 3-state buses

possible within the FPGA.

Programmable Function Unit

The PFUs are used for logic. Each PFU has 53 exter-

nal inputs and 20 outputs and can operate in several

modes. The functionality of the inputs and outputs

depends on the operating mode.

The PFU uses 36 data input lines for the LUTs, eight

data input lines for the latches/FFs, eight control inputs

(CLK[1:0], CE[1:0], LSR[1:0], SEL[1:0]), and a carry

input (CIN) for fast arithmetic functions and general-

purpose data input for the ninth FF. There are eight

combinatorial data outputs (one from each LUT), eight

latched/registered outputs (one from each latch/FF), a

carry-out (COUT), and a registered carry-out (REG-

COUT) that comes from the ninth FF. The carry-out sig-

nals are used principally for fast arithmetic functions.

There are also two dedicated F6 mode outputs which

are for the 6-input LUT function and 8-to-1 MUX.

Figure 2 and Figure 3 show high-level and detailed

views of the ports in the PFU, respectively. The eight

sets of LUT inputs are labeled as K0 through K7 with

each of the four inputs to each LUT having a suffix

of _x, where x is a number from 0 to 3.

There are four F5 inputs labeled A through D. These

are used for additional LUT inputs for 5- and 6-input

LUTs or as a selector for multiplexing two 4-input LUTs.

Four adjacent LUT4s can also be multiplexed together

with a 4-to-1 MUX to create a 6-input LUT. The eight

direct data inputs to the latches/FFs are labeled as

DIN[7:0]. Registered LUT outputs are shown as Q[7:0],

and combinatorial LUT outputs are labeled as F[7:0].

The PFU implements combinatorial logic in the LUTs

and sequential logic in the latches/FFs. The LUTs are

static random access memory (SRAM) and can be

used for read/write or ROM.

Each latch/FF can accept data from its associated LUT.

Alternatively, the latches/FFs can accept direct data

from DIN[7:0], eliminating the LUT delay if no combina-

torial function is needed. Additionally, the CIN input can

be used as a direct data source for the ninth FF. The

LUT outputs can bypass the latches/FFs, which

reduces the delay out of the PFU. It is possible to use

the LUTs and latches/FFs more or less independently,

allowing, for instance, a comparator function in the

LUTs simultaneously with a shift register in the FFs.

8

Lucent Technologies Inc.

Share Link: