WM9701 데이터 시트보기 (PDF) - Wolfson Microelectronics plc

부품명

상세내역

제조사

WM9701

Low Power AC’97 Multimedia Audio Codec

Wolfson Microelectronics plc 

Production Data

WM9701A

If a sample stream of resolution less than 20-bits is transferred, the AC’97 controller must stuff all

trailing non-valid bit positions within this time slot with 0s.

SLOT 5: OPTIONAL MODEM LINE CODEC

Audio output frame slot 5 contains the MSB justified modem DAC input data. This optional AC’97

feature is not supported in WM9701A, and if data is written to this location it is ignored. This may be

determined by the AC’97 controller interrogating the WM9701A Vendor ID registers.

SLOTS 6-12: RESERVED

Audio output frame slots 6-12 are reserved for future use and are always stuffed with 0s by the

AC’97 controller.

AC-LINK AUDIO INPUT FRAME (SDATA_IN)

The audio input frame data streams correspond to the multiplexed bundles of all digital input data

targeting the AC’97 controller. As is the case for audio output frame, each AC-link audio input frame

consists of 12, 20-bit time slots.

Slot 0 is a special reserved time slot containing 16-bits, which are used for AC-link protocol

infrastructure.

Within slot 0 the first bit is a global bit (SDATA_IN slot 0, bit 15) which flags whether WM9701A is in

the “Codec Ready” state or not. If the “Codec Ready” bit is a 0, this indicates that WM9701A is not

ready for normal operation. This condition is normal following the desertion of power on reset for

example, while WM9701A’s voltage references settle. When the AC-link “Codec Ready” indicator bit

is a 1 it indicates that the AC-link and WM9701A control and status registers are in a fully

operational state. The AC’97 controller must further probe the power down Control/Status Register to

determine exactly which subsections, if any, are ready.

Prior to any attempts at putting WM9701A into operation the AC’97 controller should poll the first bit

in the audio input frame (SDATA_IN slot 0, bit 15) for an indication that WM9701A has gone “Codec

Ready”.

Once WM9701A is sampled “Codec Ready” then the next 12 bit positions sampled by the AC’97

controller indicate which of the corresponding 12 time slots are assigned to input data streams, and

that they contain valid data. Figure 10 illustrates the time slot based AC-link protocol.

There are several subsections within WM9701A that can independently go busy/ready. It is the

responsibility of the WM9701A controller to probe more deeply into the WM9701A register file to

determine which WM9701A subsections are actually ready.

WM9701A samples SYNC assertion

SYNC

AC’97 Controller samples first

SDATA_IN bit of frame here

BIT_CLK

SDATA_IN

Codec

Ready

Slot (1) Slot (2)

End of previous Audio Frame

Figure 11 Start of an Audio Input Frame

A new audio input frame begins with a low to high transition of SYNC as shown in Figure 11. SYNC

is synchronous to the rising edge of BIT_CLK. On the immediately following falling edge of BIT_CLK,

WM9701A samples the assertion of SYNC. This falling edge marks the time when both sides of AC-

link are aware of the start of a new audio frame. On the next rising edge of BIT_CLK, the AC’97

controller transitions SDATA_IN into the first bit position of slot 0 (valid frame bit). Each new bit

position is presented to AC-link on a rising edge of BIT_CLK, and subsequently sampled by the

AC’97 controller on the following falling edge of BIT_CLK. This sequence ensures that data

transitions and subsequent sample points for both incoming and outgoing data streams are time

aligned.

SDATA_IN’s composite stream is MSB justified (MSB first) with all non-valid bit positions (for

assigned and/or unassigned time slots) stuffed with 0’s by WM9701A. SDATA_IN is sampled on the

falling edges of BIT_CLK .

WOLFSON MICROELECTRONICS LTD.

PD Rev 3.2 January 2001

13

Share Link: