AP393A 데이터 시트보기 (PDF) - Diodes Incorporated.
부품명
상세내역
제조사
AP393A Datasheet PDF : 15 Pages
| |||
AP393A
LOW POWER LOW OFFSET VOLTAGE DUAL
COMPARATORS
Electrical Characteristics (Continued)
( VCC = 5V ) ( Note 6 )
Symbol
Parameter
Conditions
Min
VOFFSET Input Offset Voltage
(Note 11)
-
IOFFSET Input Offset Current
IIN(+) -IIN(-), VCM = 0V
-
IBIAS
Input Bias Current
IIN(+) or IIN(-) with Output In
Linear Range, VCM = 0V
-
(Note 7)
Input Common Mode Voltage
Range
V+
=30V
(Note
8)
0
VSAT
Saturation Voltage
VIN(-) = 1V, VIN(+) = 0,
ISINK ≤ 4mA
-
IO(Leak) Output Leakage Current
VIN(-) = 0, VIN(+) = 1V,
VO = 30V
-
Differential Input Voltage
Keep All VIN’s ≥ 0V (or V-, if
Used), (Note 10)
-
θJA
Thermal Resistance
Junction-to-Ambient
MSOP-8L (Note 12)
SOP-8L (Note 12)
θJC
Thermal Resistance
Junction-to-Case
MSOP-8L (Note 12)
SOP-8L (Note 12)
Typ. Max Unit
-
9
mV
-
180 nA
-
500 nA
- V+ -2.0 V
-
700 mV
-
1.0 μA
-
36
V
208
165
oC/W
39
26
oC/W
Notes:
3. For operating at high temperatures, the AP393A must be derated based on a 125°C maximum junction temperature and a
thermal resistance of 170°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient.
The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small (PD <100mW), provided the
output transistors are allowed to saturate.
4. Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to
ground, the maximum output current is approximately 20mA independent of the magnitude of V+.
5. This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base
junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this
diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output
voltages of the comparators to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input
is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which is negative,
again returns to a value greater than -0.3V.
6. The AP393A temperature specifications are limited to 0°C < TOP < +70°C.
7. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent
of the state of the output so no loading change exists on the reference or input lines.
8. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The
upper end of the common-mode voltage range is V+-1.5V at 25°C, but either or both inputs can go to 36V without damage,
independent of the magnitude of V+.
9. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be
obtained, see typical performance characteristics section.
10. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than
-0.3V (or 0.3V below the magnitude of the negative power supply, if used).
11. At output switch point, VO ~ 1.4V, RS=0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+-1.5V), at 25°C.
12. Test condition for MSOP-8L and SOP-8L: Device mounted on FR-4 substrate PC board, 2oz copper, with minimum recommended pad layout.
AP393A Rev. 7
5 of 15
www.diodes.com
FEBRUARY 2009
© Diodes Incorporated
Share Link: 