HIP1030AS 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
HIP1030AS Datasheet PDF : 5 Pages
| |||
HIP1030
Absolute Maximum Ratings
Maximum Supply Voltage VCC . . . See O.V. Shutdown Limit, VOVSD
Input Voltage, VIN (Note 1) . . . . . . . . . . . . . . . . . -1V to (VCC - 0.5V)
Load Current, IOUT . . . . . . . . . . . . . . . . . . . . . . . . . Internal Limiting
Load Dump (Survival) . . . . . . . . . . . . . . . . . . . . . . . . . . ±60VPEAK
Reverse Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -16V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W) θJC (oC/W)
Plastic SIP Package . . . . . . . . . . . . . .
50
4
Maximum Power Dissipation (Note 3)
At TA =
Maximum
125oC, Infinite Heat Sink.
Junction Temperature, TJ
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6.25W
150oC
Maximum Storage Temperature Range . . . . . . . . . .-40oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. The Input Control Voltage, VIN shall not be greater than (VCC - 0.5V) and shall not exceed +7V when VCC is greater than 7.5V.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
3. The worst case thermal resistance, θJC for the SIP TS-001AA 5 lead package is 4oC/W. The calculation for dissipation and junction
temperature rise due to dissipation is:
PD = (VCC-VOUT)(IOUT) + (VCC)(ICCMAX - IOUT) or (VCC)(ICCMAX) - (VOUT)(IOUT)
TJ = TAMBIENT + (PD) (θJC) for an infinite Heat Sink.
Refer to Figure 1 for Derating based on Dissipation and Thermal Resistance. Derating from 150oC is based on the reciprocal of thermal
resistance, θJC + θHS. For example:
the junction-to-air thermal resistance,
θWJAh=er1e0θoJCC/W= .4TohCe/Wrefaonred,
gfoivretnheθHmSax=im6ouCm/Wallaoswtehdedthisesrimpaatliorne,sidsetarantcee0o.f1aWn/oeCxteforrnaelaHcheadteSgirneke,
from TAMB to the maximum rated junction temperature of 150oC. If TAMB = 100oC, the maximum PD is (150 - 100) x 0.1W/oC = 5W.
Electrical Specifications TA = -40oC to 125oC, VIN = 2V, VCC = +12V, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Operating Voltage Range
Over-Voltage Shutdown
Over-Temperature Limiting
Negative Pulse
Output Clamp Voltage
VCC
4.5
-
25
V
VOVSD
TSD
RL = 1KΩ; VIN = 2V
26
33
-
150
38
V
-
oC
VCL
ICL = -100mA; VCC = 4.5V to 25V (VCC - 35) (VCC - 30.5) (VCC - 28)
V
Short Circuit Current Limiting
Input Control ON
Input Control OFF
Input Current High
Input Current Low
Supply Current, Full Load
Input Control ON
ISC
VIH
VIL
IIH
IIL
ICCMAX
(Note 4)
VIN = 5.5V, VCC = 6V to 24V
VIN = 0.8V, VCC = 6V to 24V
VIN = 2V; IOUT = 1.0A;
1.1
1.6
2.0
-
-
-
6
-
6
-
-
1.05
2.5
A
-
V
0.8
V
40
µA
30
µA
1.1
A
Supply Current, No Load
Input Control OFF
ICCMIN VIN = 0V; IOUT = 0A;
-
55
100
µA
Input-Output Forward Voltage
VSAT IOUT = 1A; VCC = 4.5V to 25V
-
0.6
1
V
Drop (VCC - VOUT)
Output Leakage
IOUT_LK VIN = 0.8V; VCC = 6V to 24V
-
4
50
µA
Turn ON Time
tON
RL = 80Ω; (Note 5)
-
5
20
µs
Turn OFF Time
tOFF
RL = 80Ω; (Note 5)
-
25
65
µs
NOTES:
4. Short circuit current will be reduced when thermal shutdown occurs. Testing of short circuit current may require a short duration pulse.
See Figure 7.
5. Refer to Figures 3A and 3B for typical switching speeds with a 20Ω Load.
2
Share Link: 