8Mb
SMART 5 BOOT BLOCK FLASH MEMORY
PIN DESCRIPTIONS
44-PIN SOP
NUMBERS
43
40-PIN
TSOP
NUMBERS
9
48-PIN
TSOP
NUMBERS
11
–
12
14
12
22
26
44
10
12
14
24
28
33
–
47
11, 10, 9, 8,
7, 6, 5, 4,
42, 41, 40,
39, 38, 37,
36, 35, 34,
3, 2
31
21, 20, 19,
18, 17, 16,
15, 14, 8, 7,
36, 6, 5, 4,
3, 2, 1, 40,
13, 37
–
25, 24,
23,22, 21,
20, 19, 18,
8, 7, 6, 5, 4,
3, 2, 1, 48,
17, 16
45
15, 17, 19,
21, 24, 26,
28, 30
16, 18, 20,
22, 25, 27,
29
1
25-28, 32-35
–
11
29, 31, 33,
35, 38, 40,
42, 44
30, 32, 34,
36, 39, 41,
43
13
23
13, 32
–
30, 31
23, 39
29, 38
37
27, 46
9, 10, 15
SYMBOL
WE#
WP#
CE#
RP#
OE#
BYTE#
A0–A18/
(A19)
DQ15/
(A-1)
DQ0–DQ7
DQ8–
DQ14
VPP
VCC
VSS
NC
TYPE
Input
Input
Input
Input
Input
Input
Input
DESCRIPTION
Write Enable: Determines if a given cycle is a WRITE cycle.
If WE# is LOW, the cycle is either a WRITE to the command
execution logic (CEL) or to the memory array.
Write Protect: Unlocks the boot block when HIGH if VPP =
VPPH (5V) and RP# = VIH during a WRITE or ERASE. Does
not affect WRITE or ERASE operation on other blocks.
Chip Enable: Activates the device when LOW. When CE# is
HIGH, the device is disabled and goes into standby power
mode.
Reset/Power-Down: When LOW, RP# clears the status
register, sets the internal state machine (ISM) to the array
read mode and places the device in deep power-down
mode. All inputs, including CE#, are “Don’t Care,” and all
outputs are High-Z. RP# unlocks the boot block and
overrides the condition of WP# when at VHH; RP# must be
held at VIH during all other modes of operation.
Output Enable: Enables data output buffers when LOW.
When OE# is HIGH, the output buffers are disabled.
Byte Enable: If BYTE# = HIGH, the upper byte is active
through DQ8–DQ15. If BYTE# = LOW, DQ8–DQ14 are High-
Z, and all data is accessed through DQ0–DQ7. DQ15/(A - 1)
becomes the least significant address input.
Address Inputs: Select a unique 16-bit word or 8-bit byte.
The DQ15/(A - 1) input becomes the lowest order address
when BYTE# = LOW (MT28F800B5) to allow for a selection
of an 8-bit byte from the 1,048,576 available.
Input/
Output
Input/
Output
Input/
Output
Supply
Supply
Supply
–
Data I/O: MSB of data when BYTE# = HIGH.
Address Input: LSB of address input when BYTE# = LOW
during READ or WRITE operation.
Data I/Os: Data output pins during any READ operation or
data input pins during a WRITE. These pins are used to
input commands to the CEL.
Data I/Os: Data output pins during any READ operation or
data input pins during a WRITE when BYTE# = HIGH. These
pins are High-Z when BYTE# is LOW.
Write/Erase Supply Voltage: From a WRITE or ERASE
CONFIRM until completion of the WRITE or ERASE, VPP
must be at 5V. VPP = “Don’t Care” during all other
operations.
Power Supply: +5V ±10%.
Ground.
No Connect: These pins may be driven or left unconnected.
8Mb Smart 5 Boot Block Flash Memory
MT28F800B5_3.fm - Rev. 3, Pub. 8/2002
4Micron Technology, Inc. Reserves the right to change products or specifications without notice.
©2002, Micron Technology Inc.