MC100EL34 데이터 시트보기 (PDF) - ON Semiconductor

부품명

상세내역

제조사

MC100EL34

5V ECL ÷2, ÷4, ÷8 Clock Generation Chip

ON Semiconductor 

MC10EL34, MC100EL34

Table 8. 100EL SERIES NECL DC CHARACTERISTICS VCC = 0 V; VEE = −5.0 V (Note 11)

−40°C

25°C

85°C

Symbol

Characteristic

Min Typ Max Min Typ Max Min Typ Max Unit

IEE

Power Supply Current

39

39

42 mA

VOH

Output HIGH Voltage (Note 12)

−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV

VOL

Output LOW Voltage (Note 12)

−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV

VIH

Input HIGH Voltage (Single−Ended) −1165

−880 −1165

−880 −1165

−880 mV

VIL

Input LOW Voltage (Single−Ended) −1810

−1475 −1810

−1475 −1810

−1475 mV

VBB

Output Voltage Reference

−1.38

−1.26 −1.38

−1.26 −1.38

−1.26 V

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 13)

−2.8

−0.4 −2.8

−0.4 −2.8

−0.4 V

IIH

Input HIGH Current

IIL

Input LOW Current

150

150

150 mA

0.5

0.5

0.5

mA

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.

12. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.

13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input

signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.

Table 9. AC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −5.0 V (Note 14)

−40°C

25°C

85°C

Symbol

Characteristic

fmax

Maximum Toggle Frequency

tPLH

Propagation

tPHL

Delay to

Output

CLK to Q0

CLK to Q1,2

MR to Q

Min Typ Max Min Typ Max Min Typ Max Unit

1.1

1.1

1.1

GHz

960

1200 960

1200 970

1210 ps

900

1140 900

1140 910

1150

750

1060 750

1060 790

1090

tSKEW

tJITTER

tS

tH

tRR

VPP

tr

tf

Within-Device Skew (Note 15)

Cycle−to−Cycle Jitter

Setup Time EN

Hold Time EN

Set/Reset Recovery

Input Swing (Note 16)

Output Rise/Fall Times Q

(20% − 80%)

100

100

100

ps

1.0

1.0

1.0

ps

400

400

400

ps

250

250

250

ps

400 200

400 200

400 200

ps

150

1000 150

1000 150

1000 mV

225

475 225

475 225

475 ps

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

14. 10 Series: VEE can vary +0.06 V / −0.5 V.

100 Series: VEE can vary +0.8 V / −0.5 V.

15. Within-device skew is defined as identical transitions on similar paths through a device.

16. VPPmin is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40.

http://onsemi.com

5

Share Link: