74ALS374N 데이터 시트보기 (PDF) - Philips Electronics

부품명

상세내역

제조사

74ALS374N

Latch/flip–flop

Philips Electronics 

Philips Semiconductors

Latch/flip-flop

Product specification

74ALS373/74ALS374

74ALS373 Octal transparent latch (3-State)

74ALS374 Octal D flip-flop (3-State)

FEATURES

• 8-bit transparent latch – 74ALS373

• 8-bit positive edge triggered register – 74ALS374

• 3-State output buffers

• Common 3-State output register

• Independent register and 3-State buffer operation

TYPE

TYPICAL

PROPAGATION DELAY

74ALS373

6.0ns

TYPICAL

SUPPLY CURRENT

(TOTAL)

14mA

TYPE

74ALS374

TYPICAL

fMAX

50MHz

TYPICAL

SUPPLY CURRENT

(TOTAL)

17mA

ORDERING INFORMATION

DESCRIPTION

ORDER CODE

COMMERCIAL RANGE

VCC = 5V ±10%,

Tamb = 0°C to +70°C

DRAWING

NUMBER

20-pin plastic DIP 74ALS373N, 74ALS374N SOT146-1

20-pin plastic SOL 74ALS373D, 74ALS374D SOT163-1

20-pin plastic SSOP

Type II

74ALS373DB, 74ALS374DB

SOT339-1

DESCRIPTION

The 74ALS373 is an octal transparent latch coupled to eight 3-State

output devices. The two sections of the device are controlled

independently by enable (E) and output enable (OE) control gates.

The data on the D inputs is transferred to the latch outputs when the

enable (E) input is High. The latch remains transparent to the data

input while E is High, and stores the data that is present one setup

time before the High-to-Low enable transition.

The 3-State output buffers are designed to drive heavily loaded

3-State buses, MOS memories, or MOS microprocessors.

The active-Low output enable (OE) controls all eight 3-State buffers

independent of the latch operation. When OE is Low, latched or

transparent data appears at the output.

When OE is High, the outputs are in High impedance “off” state,

which means they will neither drive nor load the bus.

The 74ALS374 is an 8-bit edge triggered register coupled to eight

3-State output buffers. The two sections of the device are controlled

independently by clock (CP) and output enable (OE) control gates.

The register is fully edge triggered. The state of the D input, one

setup time before the Low-to-High clock transition is transferred to

the corresponding flip-flop’s Q output.

The 3-State output buffers are designed to drive heavily loaded

3-State buses, MOS memories, or MOS microprocessors.

The active-Low output enable (OE) controls all eight 3-State buffers

independent of the register operation. When OE is Low, the data in

the register appears at the outputs. When OE is High, the outputs

are in High impedance “off” state, which means they will neither

drive nor load the bus.

INPUT AND OUTPUT LOADING AND FAN-OUT TABLE

PINS

DESCRIPTION

74ALS (U.L.)

HIGH/LOW

D0 – D7

Data inputs

1.0/1.0

E (74ALS373)

Enable input (active-High)

1.0/1.0

OE

Output enable inputs (active-Low)

1.0/1.0

CP (74ALS374)

Clock pulse input (active rising edge)

1.0/1.0

Q0 – Q7

3-State outputs

130/240

NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.

LOAD VALUE

HIGH/LOW

20µA/0.1mA

20µA/0.1mA

20µA/0.1mA

20µA/0.1mA

2.6mA/24mA

1991 Feb 08

2

853–1243 01670

Share Link: