VT16245BDL 데이터 시트보기 (PDF) - Philips Electronics

부품명

상세내역

제조사

VT16245BDL

3.3V ABT 16-bit transceiver (3-State)

Philips Electronics 

Philips Semiconductors

3.3V 16-bit transceiver (3-State)

Product specification

74LVT16245B

DC ELECTRICAL CHARACTERISTICS

LIMITS

SYMBOL

PARAMETER

TEST CONDITIONS

Temp = -40°C to +85°C

MIN TYP1 MAX

UNIT

VIK

Input clamp voltage

VCC = 2.7V; IIK = –18mA

–0.85 –1.2

V

VCC = 2.7 to 3.6V; IOH = –100µA

VCC-0.2 VCC

VOH

High-level output voltage

VCC = 2.7V; IOH = –8mA

2.4

2.5

V

VCC = 3.0V; IOH = –32mA

2.0

2.3

VCC = 2.7V; IOL = 100µA

0.07 0.2

VCC = 2.7V; IOL = 24mA

0.3 0.5

VOL

Low–level output voltage

VCC = 3.0V; IOL = 16mA

0.25 0.4

V

VCC = 3.0V; IOL = 32mA

0.3 0.5

VCC = 3.0V; IOL = 64mA

0.4 0.55

VCC = 3.6V; VI = VCC or GND

VCC = 0 or 3.6V; VI = 5.5V

Control pins

0.1

±1

0.1

10

II

Input leakage current

VCC = 3.6V; VI = 5.5V

VCC = 3.6V; VI = VCC

I/O Data pins4

0.1

20

µA

0.5

10

VCC = 3.6V; VI = 0

0.1

-5

IOFF

Output off current

VCC = 0V; VI or VO = 0 to 4.5V

0.1 ±100 µA

IHOLD

Bus Hold current

A or B outputs6

VCC = 3V; VI = 0.8V

VCC = 3V; VI = 2.0V

VCC = 0V to 3.6V; VCC = 3.6V

75

135

-75 -135

µA

±500

IEX

Current into an output in the

High state when VO > VCC

VO = 5.5V; VCC = 3.0V

75

125

µA

IPU/PD

Power up/down 3-State output VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC;

current3

OE/OE = Don’t care

40 ±100 µA

ICCH

VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0

0.07 0.12

ICCL

Quiescent supply current

VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0

4.7

6

mA

ICCZ

VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05

0.07 0.12

∆ICC

Additional supply current per

input pin2

VCC = 3V to 3.6V; One input at VCC-0.6V,

Other inputs at VCC or GND

0.1 0.2 mA

NOTES:

1. All typical values are at VCC = 3.3V and Tamb = 25°C.

2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND

3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a

transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.

4. Unused pins at VCC or GND.

5. ICCZ is measured with outputs pulled to VCC or GND.

6. This is the bus hold overdrive current required to force the input to the opposite logic state.

1998 Feb 19

5

Share Link: