ACE9030M 데이터 시트보기 (PDF) - Mitel Networks

부품명

상세내역

제조사

ACE9030M

Radio Interface and Twin Synthesiser

Mitel Networks 

ACE9030

ELECTRICAL CHARACTERISTICS

These characteristics apply over these ranges of conditions (unless otherwise stated):

TAMB = – 40 °C to + 85 °C, VDD = + 3·6 to + 5·0 V, GND ref. = VSS

D.C. Characteristics

Parameter

Power supply

Supply current, Radio Interface:

Sleep mode

Fully operating (excluding IDDX)

Supply current, Synthesisers: VDD=5V

Main and Auxiliary ON

Main ON and Auxiliary in Standby

Main in Standby and Auxiliary ON

Main and Auxiliary in Standby, with Bandgap off

Supply current, Synthesisers:

Main and Auxiliary ON

Main ON and Auxiliary in Standby

Main in Standby and Auxiliary ON

Main and Auxiliary in Standby

Input and output signals

Logic input HIGH (LATCHC, LATCHB, DATA,

CL, and TEST)

Logic input LOW (LATCHC, LATCHB, DATA,

CL, and TEST)

Input capacitance (signal pins)

Input leakage (signal pins)

Logic output HIGH (RXCD, DATA, AFCOUT,

TEST and DOUT2, 3 and 4)

Logic output LOW (RXCD, DATA, AFCOUT,

TEST and DOUT2, 3 and 4)

Output ON level, DOUT0 and DOUT1

Output HIGH level, DOUT5, 6 and 7

Output LOW level, DOUT5, 6 and 7

Trimmed output level ON, DOUT8

Level difference, DOUT8 ON – ADC reference

Output level OFF, DOUT8

MODMP, MODMN output HIGH

MODMP, MODMN output LOW

Input Schmitt Hysteresis, pins CL, LATCHB,

LATCHC, DATA.

Analog circuits bias resistor on IREF

Min.

Typ.

Max.

Unit Conditions

2.3

2·7

mA XO, OSC8 on

7

mA (see Note 1)

fREF = 10 MHz

5

mA fMAIN = 10 MHz

3.7

mA fAUX = 10 MHz

3

mA (see Note 2)

100

µA

fREF = 15 MHz

3

mA fMAIN = 16 MHz

2

mA fAUX = 90 MHz

2

mA (see Note 2)

100

µA

0·7 x VDD

– 0·3

VDD – 0·5

VDDX – 0·2

2·3

3·35

–5

VDD/2 + 0·35

VDD/2 – 1·0

0·3

VDD + 0·3

+ 0·8

10

1

0·4

V

V

pF Pin voltage

µA VSS to VDD

V

External load:

V 20 kΩ & 30 pF

2·9

0·3

3·55

+ 15

0.4

VDD/2 + 1·0

VDD/2 – 0·35

V IOH = 20 mA.

V IOH = 80 µA

V IOL = 0.2 µA

V IOH = 135 to 400 µA.

mV

V

V IOH = 10 µA

V IOL = – 10 µA

V

68

kΩ VDD @ 3·75 V

100

kΩ VDD @ 4·85 V

Notes

1. The sleep current is specified with the crystal oscillator (XO) and the OSC8 oscillator and PLL running as these are normally needed to provide

the clock to the system controller.

2. The terms fREF, fMAIN, and fAUX refer to the frequencies of the Reference inputs (Crystal oscillator, pins CIN1 and CIN2), the Main synthesiser

inputs (pins FIM and FIMB) and the Auxiliary synthesiser inputs (pins FIA and FIAB) respectively.

5

Share Link: