ACPL-4800-060E 데이터 시트보기 (PDF) - Avago Technologies

부품명

상세내역

제조사

ACPL-4800-060E

High CMR Intelligent Power Module and Gate Drive Interface Optocoupler

Avago Technologies 

Switching Specifications (AC)

-40°C ≤ TA ≤ 100°C, 4.5V ≤ VCC ≤ 20V, 6mA ≤ IF(ON) ≤ 10 mA, 0V ≤ VF(OFF) ≤ 0.8V.

All Typicals at TA = 25°C, IF(ON) = 6 mA unless otherwise specified.

Parameter

Sym.

Min.

Typ. Max. Units Test Conditions

Fig. Note

Propagation Delay Time tPHL

to Logic Low Output

Leve

150 350 ns With Peaking Capacitor

5,6 5

Propagation Delay Time tPLH

to Logic High Output

Level

110 350 ns With Peaking Capacitor

5,6 5

Pulse Width Distortion PWD

250 ns

| tPHL - tPLH |

8

Propagation Delay Dif- PDD -100

250 ns

10

ference Between Any 2

Parts

Output Rise Time (10- tr

16

ns

5,8

90%)

Output Fall Time (90-

tf

20

ns

5,8

10%)

Logic High Common

Mode Transient Immu-

nity

|CMH|

-30000

V/ms |VCM| = 1000 V, IF = 6.0 mA, 9

6

VCC = 5 V, TA = 25 C

Logic Low Common

Mode Transient Immu-

nity

|CML|

30000

V/ms |VCM| = 1000 V, VF = 0 V, VCC 9

6

= 5 V, TA = 25 C

Package Characteristics

Parameter

Sym. Min.

Typ.

Max. Units Test Conditions

Fig. Note

Input-Output Momentary VISO 3750

Withstand Voltage*

Vrms RH < 50%, t = 1 min.TA

4,7

= 25°C

Input-Output Resistance RI-O

1012

W

VI-O = 500 Vdc

4

Input-Output Capacitance CI-O

0.6

pF

f = 1 MHz, VI-O = 0 Vdc

4

* The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage

rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level

safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E.

Notes:

1. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.

2. Duration of output short circuit time should not exceed 10 ms.

3. Input capacitance is measured between pin 2 and pin 3.

4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.

5. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the

output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing

edge of the output pulse.

6. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V. CML

is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.

7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for one second (leakage detec-

tion current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN

60747-5-2 Insulation Characteristics Table, if applicable.

8. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH | for any given device.

9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.

10. The difference between tPLH and tPHL between any two devices under the same test condition.



Share Link: