ACPL-M61T 데이터 시트보기 (PDF) - Avago Technologies
부품명
상세내역
제조사
ACPL-M61T Datasheet PDF : 10 Pages
| |||
Package Characteristics
Parameter
Symbol Min. Typ. Max. Units Test Conditions
Fig. Note
Input-Output Momentary Withstand VISO 4000
Voltage*
Vrms RH ≤ 50%, t = 1 min;TA =
25°C
Input-Output Resistance
RI-O
1014
Ω
VI-O = 500 Vdc
Input-Output Capacitance
CI-O
0.6
pF
f = 1 MHz; VI-O = 0 Vdc
* The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or Avago Technologies Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Switching Specifications (AC)
Over recommended temperature TA = -40°C to 125°C, VCC = 5.0 V, IF = 6.5mA unless Otherwise Specified.
Parameter
Symbol Min. Typ. Max. Units Test Conditions
Fig. Note
Propagation Delay Time
tPHL
to Low Output Level
Propagation Delay Time
tPLH
to High Output Level
46 75 ns
100 ns
50 75 ns
100 ns
TA=25°C
TA=25°C
RL = 350Ω
CL = 15pF
IF = 6.5mA
6, 7, 8 6
6, 7, 8 5
Propagation Delay Skew
tPSK
40 ns
14, 15 10,
11
Pulse Width Distortion
Output Rise Time (10% -
90%)
| tPHL - tPLH|
trise
3.5 35 ns
24
ns
9
10
10
Output Fall Time (10% - 90%) tfall
10
ns
10
Common Mode Transient
Immunity at High Output
Level
|CMH|
15 30
kV/μs VCM=1000Vp-p Vo(min) = 2V 11
7,9
IF = 0mA
TA=25°C
RL=350Ω
Common Mode Transient
Immunity at Low Output
Level
|CML|
15 30
kV/μs VCM=1000Vp-p Vo(max) = 0.8V
8,9
IF = 6.5mA
TA=25°C
RL=350Ω
*All Typicals at TA = 25°C, Vcc = 5V.
Notes:
1. Bypassing of the power supply line is required with a 0.1 μF ceramic disc capacitor adjacent to each optocoupler. The total lead length between
both ends of the capacitor and the isolator pins should not exceed 10 mm.
2. Peaking circuits may produce transient input currents up to 40 mA, 50 ns maximum pulse width, provided average current does not exceed 20
mA.
3. Device considered a two terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together.
4. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4800 VRMS for 1 second.
5. The tPLH propagation delay is measured from 3.25 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the
output pulse.
6. The tPHL propagation delay is measured from 3.25 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the
output pulse.
7. CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., VOUT > 2.0 V).
8. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., VOUT < 0.8 V).
9. For sinusoidal voltages, (|dVCM|/dt)max = SfCMVCM(p-p).
10. See application section; “Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew” for more information.
11. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the worst case
operating condition range.
12. Input current derates linearly above 85°C free-air temperature at a rate of 0.25 mA/°C.
13. Input power derates linearly above 85°C free-air temperature at a rate of 0.375mW/°C.
14. Output power derates linearly above 85°C free-air temperature at a rate of 0.475 mW/°C.
5
Share Link: 