ACPL-W456-000E 데이터 시트보기 (PDF) - Avago Technologies
부품명
상세내역
제조사
ACPL-W456-000E Datasheet PDF : 12 Pages
| |||
Table 6. Switching Specifications (RL= 20 kΩ)
Over recommended operating conditions unless otherwise specified. TA = -40°C to +100°C, VCC = +4.5 V to 30 V, IF(on) =
10 mA to 20 mA, VF(off) = -5 V to 0.8 V
Parameter
Symbol Min. Typ. Max. Units Test Conditions
Fig.
Note
Propagation Delay Time
to Low Output Level
Propagation Delay Time
to High Output Level
tPHL
30
200 400 ns
CL = 100 IF(on) = 10 mA, 5, 7 -11 8, 9
pF
VF(off) = 0.8 V,
100
ns
CL = 10 pF
VCC = 15.0 V,
VTHLH = 2.0 V,
tPLH
270 400 550 ns
CL = 100 VTHHL = 1.5 V
pF
130
ns
CL = 10 pF
Pulse Width Distortion
PWD
200 450 ns CL = 100
13
pF
Propagation Delay Difference tPLH-tPHL -150 200 450 ns
10
Between Any 2 Parts
Output High Level Common |CMH| 15 30
Mode Transient Immunity
Output Low Level Common
|CML|
15
30
Mode Transient Immunity
kV/μs IF = 0 mA, VCC = 15.0 V,
6
11
VO > 3.0 V CL = 100 pF,
kV/μs
IF = 10 mA,
VO < 1.0 V
VCM = 1500 VP-P,
TA = 25°C
12
*All typical values at 25°C, VCC = 15 V.
Table 7. Package Characteristics
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Symbol
VISO
RI-O
CI-O
Min. Typ. Max.
3750
5000 (For ACPL-W456)
1012
0.6
Units
Vrms
Test Conditions
RH < 50%, t = 1 min,
TA = 25°C
:
VI-O = 500 Vdc
pF Freq=1 MHz
Fig. Note
6, 7
6
6
Notes:
1. Derate linearly above 90°C free-air temperature at a rate of 0.8 mA/°C.
2. Derate linearly above 90°C free-air temperature at a rate of 1.6 mA/°C.
3. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/°C.
4. Derate linearly above 90°C free-air temperature at a rate of 4.2 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current (IO) to the forward LED input current (IF) times 100.
6. Device considered a two-terminal device: Pins 1 and 3 shorted together and Pins 4, 5 and 6 shorted together.
7. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for 1 second (leakage detection
current limit, II-O ≤ 5 μA) ; each optocoupler under ACPL-W456 is proof tested by applying an insulation test voltage ≥ 6000 VRMS for 1 second
(leakage detection current limit, II-O ≤ 5 μA).
8. Pulse: f = 20 kHz, Duty Cycle = 10%.
9. Use of a 0.1 μF bypass capacitor connected between pins 4 and 6 can improve performance by filtering power supply line noise.
10. The difference between tPLH and tPHL between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay
Specifications section.)
11. Common mode transient immunity in a Logic High level is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the
output will remain in a Logic High state (i.e., VO > 3.0 V).
12. Common mode transient immunity in a Logic Low level is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the
output will remain in a Logic Low state (i.e., VO < 1.0 V).
13. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH| for any given device.
6
Share Link: 