AD7280DSTZ 데이터 시트보기 (PDF) - Analog Devices

부품명

상세내역

제조사

AD7280DSTZ

Lithium Ion Battery Monitoring System

Analog Devices 

AD7280

PIN CONFIGURATIONS AND FUNCTIONAL DESCRIPTIONS

Preliminary Technical Data

48 47 46 45 44 43 42 41 40 39 38 37

VIN6 1

CB6 2

VIN5 3

CB5 4

VIN4 5

CB4 6

VIN3 7

CB3 8

VIN2 9

CB2 10

VIN1 11

CB1 12

PIN 1

AD7280

TOP VIEW

36 VT3

35 VT4

34 VT5

33 VT6

32 VTTERM

31 AGND

30 AVCC

29 VDRIVE

28 ALERTlo

27 ALERT

26 SDO

25 SDOlo

13 14 15 16 17 18 19 20 21 22 23 24

VIN6 1

CB6 2

VIN5 3

CB5 4

VIN4 5

CB4 6

VIN3 7

CB3 8

VIN2 9

CB2 10

VIN1 11

CB1 12

PIN 1

INDICATOR

AD7280

TOP VIEW

36 VT3

35 VT4

34 VT5

33 VT6

32 VTTERM

31 AGND

30 AVCC

29 VDRIVE

28 ALERTlo

27 ALERT

26 SDO

25 SDOlo

Figure 2.

Figure 3.

Table 4.

Pin No.

1, 3, 5, 7,

9, 11, 13

2, 4, 6, 8,

10, 12

14

15

16

17

18

19

Mnemonic

Vin6 to

Vin0

CB6 to CB1

MASTER

PD

VDD

VSS

VREG

DVCC

Description

Analog Input 0 to Analog Input 6. Analog input 0 should be connected to the base of the series connected

battery cells. Analog Input 1 should be connected to the top of cell 1, Analog Input 2 should be connected to

the top of cell 2, etc. The Analog Inputs are multiplexed into the on-chip track-and-hold allowing the potential

across each cell to be measured.

Cell Balance Outputs. These provide a voltage output which can be used to supply the gate drives of a cell

balancing transistor network. Each CB(n) output provides a 5V voltage output referenced to the absolute

voltage of Cell(n-1).

Voltage Input. In an application with 2 or more AD7280s Daisy Chained the MASTER pin of the AD7280

connected directly to the DSP or uP should be connected to the VDD supply pin through a 10kOhm resistor. The

MASTER pin on the remaining AD7280s in the application should be tied to their respective VSS supply pins

through 10kOhm resistors.

Power down Input. This input is used to power down the AD7280. When acting as master the PD input is

supplied from the DSP/uP. When acting as a slave on the Daisy Chain the PD input should be connected to the

PDhi output of the AD7280 immediately below it in potential in the Daisy Chain. This input can also be tied to

VCC and the power down initiated through the serial interface.

Positive Power Supply Voltage. This is the positive supply voltage for the high voltage analog input structure

AD7280. The supply must be greater than a minimum voltage of 7.5 V. In an application monitoring the cell

voltages of up to 6 series connected battery cells the supply voltage may be supplied directly from the cell with

the highest potential. The maximum voltage which can be applied between VDD and VSS is 30V. Place 10 µF and

100 nF decoupling capacitors on the VDD pin.

Negative Power Supply Voltage. This is the negative supply voltage for the high voltage analog input structure

of the AD7280. This input should be at the same potential as the AGND voltage.

Analog Voltage output, 5V. The internally generated VREG voltage, which provides the supply voltage for the

ADC core, is available on this pin for use external to the AD7280. Place 10 µF and 100 nF decoupling capacitors

on the VREG pin.

Digital Supply Voltage, 4.75 V to 5.25 V. The DVCC and AVCC voltages should ideally be at the same potential.

For best performance, it is recommended that the DVCC and AVCC pins be shorted together, to ensure that the

voltage difference between them never exceeds 0.3 V even on a transient basis. This supply should be decoupled

to DGND. Place 100 nF decoupling capacitors on the DVCC pin. The DVCC supply pin should be connected to the

VREG output

Rev. PrD | Page 6 of 33

Share Link: