ADP1046A 데이터 시트보기 (PDF) - Analog Devices

부품명

상세내역

제조사

ADP1046A

Digital Controller for Isolated Power Supply Applications

Analog Devices 

Data Sheet

ADP1046A

Pin No.

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

Mnemonic

OUTD

OUTAUX

GATE

SCL

SDA

PSON

FLAGIN

PGOOD2

PGOOD1

SHAREo

SHAREi

DGND

VCORE

VDD

RTD

ADD

RES

VS3−

VS3+

EP

Description

PWM Output for Primary Side Switch. This signal is referenced to AGND. This pin can be disabled when not in use.

Auxiliary PWM Output. This signal is referenced to AGND. This pin can be disabled when not in use.

OrFET Gate Drive Output. This signal is referenced to AGND. If this pin is not used, leave it floating.

I2C Serial Clock Input. This signal is referenced to AGND.

I2C Serial Data Input and Output (Open Drain). This signal is referenced to AGND.

Power Supply On Input. This signal is referenced to AGND. This pin is the hardware PSON control signal. It is

recommended that a 1 nF capacitor be connected from the PSON pin to AGND for noise debouncing and

decoupling.

Flag Input. An external signal can be input at this pin to generate a flag condition.

Power-Good Output (Open Drain). This signal is referenced to AGND. This pin is controlled by the PGOOD2 flag.

This pin is set by a programmable combination of internal flags. If this pin is not used, connect it to AGND.

Power-Good Output (Open Drain). This signal is referenced to AGND. This pin is controlled by the PGOOD1 flag.

This pin is set by a programmable combination of internal flags. If this pin is not used, connect it to AGND.

Share Bus Output Voltage Pin. Connect this pin to 3.3 V through a pull-up resistor (typically 2.2 kΩ). When

configured for a digital share bus, this pin is a digital output. This signal is referenced to AGND. If this pin is

not used, connect it to AGND.

Share Bus Feedback Pin. Connect this pin to the SHAREo pin. This signal is referenced to AGND. If this pin is not

used, connect it to AGND.

Digital Ground. This pin is the ground reference for the digital circuitry of the ADP1046A. Star connect to AGND.

Output of the 2.5 V Regulator. Connect a decoupling capacitor of at least 330 nF (1 µF maximum) from this pin

to DGND as close to the IC as possible to minimize PCB trace length. It is recommended that the VCORE pin not

be used as a reference or to generate other logic levels using resistive dividers.

Positive Supply Input. This signal is referenced to AGND. Connect a 4.7 µF decoupling capacitor from this pin to

AGND as close to the IC as possible to minimize PCB trace length.

Thermistor Input. Place a thermistor (100 kΩ, 1%; beta = 4250, 1%) in parallel with a 16.5 kΩ, 1% resistor. This

pin is referenced to AGND. If this pin is not used, connect it to AGND.

Address Select Input. This pin is used to program the I2C address. Connect a resistor from ADD to AGND. This

signal is referenced to AGND.

Resistor Input. This pin sets up the internal voltage reference for the ADP1046A. Connect a 10 kΩ, ±0.1% resistor

from RES to AGND. This signal is referenced to AGND.

Inverting Remote Voltage Sense Input. There should be a low ohmic connection to AGND. The resistor divider

on this input must have a tolerance specification of 0.5% or better to allow for trimming. Connect a 0.1 µF

capacitor from VS3− to AGND.

Noninverting Remote Voltage Sense Input. This signal is referenced to VS3−, and the nominal input voltage at

this pin is 1 V. The resistor divider on this input must have a tolerance specification of 0.5% or better to allow for

trimming. This pin is the input to the high frequency Δ-Σ ADC.

Exposed Pad. The ADP1046A has an exposed thermal pad on the underside of the package. For increased

reliability of the solder joints and maximum thermal capability, it is recommended that the pad be soldered

to the PCB AGND plane.

Rev. 0 | Page 11 of 88

Share Link: