AS1329 데이터 시트보기 (PDF) - austriamicrosystems AG
부품명
상세내역
제조사
AS1329 Datasheet PDF : 17 Pages
| |||
AS1329
Data Sheet - Detailed Description
Low-Noise Fixed-Frequency Operation
Oscillator
The AS1329 switching frequency is internally fixed at 1.2MHz allowing the use of very small external components.
Error Amplifier
The integrated error amplifier is an internally compensated trans-conductance (gm) type (current output). The internal
1.23V reference voltage is compared to the voltage at pin FB to generate an error signal at the output of the error
amplifier. A voltage divider from VOUT to GND programs the output voltage from 2.5 to 5V via pin FB as:
VOUT = 1.23V(1 + (R1/R2))
(EQ 1)
Current Sensing
A signal representing the internal NMOS-switch current is summed with the slope compensator. The summed signal is
compared to the error amplifier output to provide a peak current control command for the PWM. Peak switch current is
limited to approximately 850mA independent of VIN or VOUT.
Zero Current Comparator
The zero current comparator monitors the inductor current to the output and shuts off the PMOS synchronous rectifier
once this current drops to 20mA (approx.). This prevents the inductor current from reversing polarity and results in
improved converter efficiency at light loads.
Anti-Ringing Control
Anti-ringing control circuitry prevents high-frequency ringing on pin SW as the inductor current approaches zero. This
is accomplished by damping the resonant circuit formed by the inductor and the capacitance on pin SW (CSW).
Powersave Operation (AS1329A, AS1329B)
In light load conditions, the integrated powersave feature removes power from all circuitry not required to monitor
VOUT. When VOUT has dropped approximately 1% from nominal, the AS1329A & B powers up and begins normal
PWM operation.
COUT (see Figure 15 on page 7) recharges, causing the AS1329A and AS1329B to re-enter powersave mode as long
as the output load remains below the powersave threshold. The frequency of this intermittent PWM is proportional to
load current; i.e., as the load current drops further below the powersave threshold, the AS1329A and AS1329B turns
on less frequently. When the load current increases above the powersave threshold, the AS1329A and AS1329B will
resume continuous, seamless PWM operation.
While the AS1329A switches to automatic powersave mode already at medium loads, the AS1329B will do so only at
very light loads.
Notes:
1. An optional capacitor (CFF) between pins VOUT and FB in some applications can reduce VOUTp-p ripple and input
quiescent current during powersave mode. Typical values for CFF range from 15 to 220pF.
2. In powersave mode the AS1329A and AS1329B draws only 30µA from the output capacitor(s), greatly improving
converter efficiency.
Shutdown
When pin SHDNN is low the AS1329 is switched off and <1µA current is drawn from battery; when pin SHDNN is high
the device is switched on. If SHDNN is driven from a logic-level output, the logic high-level (on) should be referenced
to VOUT to avoid intermittently switching the device on.
Note: If pin SHDNN is not used, it should be connected directly to pin OUT.
In shutdown the battery input is connected to the output through the inductor and the internal synchronous rectifier P-
FET. This allows the input battery to provide backup power for devices such as an idle microcontroller, memory, or real-
time-clock, without the usual diode forward drop. In this way a separate backup battery is not needed.
In cases where there is residual voltage during shutdown, some small amount of energy will be transferred from pin
OUT to pin BATT immediately after shutdown, resulting in a momentary spike of the voltage at pin BATT. The ratio of
CIN and COUT partly determine the size and duration of this spike, as does the current-sink ability of the input device.
www.austriamicrosystems.com
Revision 1.01
8 - 17
Share Link: 