CAT24C21ZE-TE13 데이터 시트보기 (PDF) - Catalyst Semiconductor => Onsemi

부품명

상세내역

제조사

CAT24C21ZE-TE13

1-kb Dual Mode Serial EEPROM for VESA™ "Plug-and-Play"

Catalyst Semiconductor => Onsemi 

CAT24C21

ABSOLUTE MAXIMUM RATINGS*

Temperature Under Bias .................. -55°C to +125°C

Storage Temperature ........................ -65°C to +150°C

Voltage on Any Pin with

Respect to Ground(1) ............ -2.0 V to VCC + 2.0 V

VCC with Respect to Ground .............. -2.0 V to +7.0 V

Package Power Dissipation

Capability (TA = 25°C) .................................. 1.0 W

Lead Soldering Temperature (10 seconds) ...... 300°C

Output Short Circuit Current(2) ....................... 100 mA

*COMMENT

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device.

These are stress ratings only, and functional operation of

the device at these or any other conditions outside of those

listed in the operational sections of this specification is not

implied. Exposure to any absolute maximum rating for

extended periods may affect device performance and

reliability.

RELIABILITY CHARACTERISTICS

Symbol Parameter

NEND(3)(*) Endurance

TDR(3)

Data Retention

VZAP(3) ESD Susceptibility

ILTH(3)(4) Latch-up

(*) Page Mode, VCC = 5 V, 25˚C

Reference Test Method

MIL-STD-883, Test Method 1033

MIL-STD-883, Test Method 1008

MIL-STD-883, Test Method 3015

JEDEC Standard 17

Min

1,000,000

100

2000

100

D.C. OPERATING CHARACTERISTICS

VCC = 2.5 V to 5.5 V, unless otherwise specified. Industrial temperature range.

Symbol

ICC

ISB(5)

ILI

ILO

VIL

VIH

VOL1

VIL

VIH

Parameter

Power Supply Current

Standby Current

Input Leakage Current

Output Leakage Current

Input Low Voltage

Input High Voltage

Output Low Voltage

Input Low Voltage (VCLK)

Input High Voltage (VCLK)

Test Conditions

fSCL = 400 kHz

VIN = GND or VCC

VIN = GND to VCC

VOUT = GND to VCC

VCC = 3.0 V, IOL = 3 mA

VCC ≥ 2.7 V

Min

–1

VCC x 0.7

2.0

Units

Program/Erase Cycles

Years

Volts

mA

Max

2

1

10

10

VCC x 0.3

VCC + 0.5

0.4

0.8

Units

mA

µA

µA

µA

V

V

V

V

V

CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5 V

Symbol Parameter

Conditions

Min

CI/O(3) Input/Output Capacitance (SDA)

VI/O = 0 V

CIN(3)

Input Capacitance (VCLK, SCL)

VIN = 0 V

Max

8

6

Units

pF

pF

Note:

(1) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC

voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods of less than 20 ns.

(2) Output shorted for no more than one second.

(3) This parameter is tested initially and after a design or process change that affects the parameter.

(4) Latch-up protection is provided for stresses up to 100 mA on I/O pins from –1 V to VCC + 1 V.

(5) Maximum standby current (ISB) = 10µA for the Extended Automotive temperature range.

Doc. No. 1032, Rev. O

2

Share Link: