CXA3503 데이터 시트보기 (PDF) - Sony Semiconductor
부품명
상세내역
제조사
CXA3503 Datasheet PDF : 42 Pages
| |||
CXA3503R
Setting Conditions for Measuring Electrical Characteristics
Use the Electrical Characteristics Measurement Circuit on page 22 when measuring electrical characteristics.
For measurement, the digital block must be initialized and power saving must be canceled by performing
Settings 1 and 2 below. In addition, the serial data must be set to the initial settings shown in the table below.
Setting 1. Horizontal AFC adjustment
Input a signal and adjust the VCO using V22 so that WL and WH of the TP24 output waveform are the same.
Setting 2. Canceling power saving mode
The power-on default is power saving mode, so clear (set all "0") serial data PS0, PS1, PS2, PS3, PS4 and
SYNC GEN.
Horizontal sync
signal
WS
WS
RPD (Pin 24)
Serial data initial settings
WL WH
WL WH
Fig. 1. Horizontal AFC adjustment
WL = WH
MSB
ADDRESS
LSB MSB
DATA
LSB
D15 D14 D13 D12 D11 D10 D9
0000000
0000000
0000001
0000001
0000010
0000010
0000011
0000011
∗1 0 0 0 0 1 0 0
0000100
0000101
0000101
0000110
0000110
0000111
0000111
0001000
0010100
0010100
0010101
0010101
0010110
D8 D7 D6 D5 D4 D3 D2 D1 D0
0
USER-BRIGHT
(01000110/LSB)
1
SUB-BRIGHT R (10001010/LSB)
0
SUB-BRIGHT B (10001010/LSB)
1
CONTRAST
(00111111/LSB)
0
SUB-CONTRAST R (10011111/LSB)
1
SUB-CONTRAST B (10011111/LSB)
0
γ-2
(11111111/LSB)
1
γ-1
(11111111/LSB)
00
0
0
0
0
0
0
0
1
COM-DC
(10000000/LSB)
0
COLOR
(00000000/LSB)
1
HUE
(10000000/LSB)
0
0
WHITE-LIMITER
(00/LSB)
BLACK-LIMITER (11111/LSB)
1 FILTER (00/LSB) 0
0
0
LPF (000/LSB)
0
PICTURE-GAIN (00000/LSB)
0
PICTURE-F0
(00/LSB)
10
0
0
0 MODE (1) DA (000/LSB)
00
0
SYNC GEN PS 4 PS 3 PS 2 PS 1 PS 0
(0) (0) (0) (0) (0) (0)
0 SLRGT (0) SLSH2 (1) SLSH1 (1) SLSH0 (1) SLSYS2 (0) SLSYS (1) SLWD (0) SLPL (0)
1 SLTST0 (0) SLFL (0) SLFR (0) SL4096 (0) SLCLP2 (0) SLCLP1 (0) SLVDP (0) SLHDP (0)
0 SLTST5 (0) SLTST4 (0) SLTST3 (0) SLTST2 (0) SLDWN (0) SLSYP (1) SLTST1 (0) SLEXVD (0)
10
0
0
H-POSITION (10000)
00
0
0
HD-POSITION (00000)
Note) If there is the possibility that data may be set at other than the above-noted addresses, set these data to "0".
When using, the address data ∗1 must be set all "0".
– 11 –
Share Link: 