GL3210 데이터 시트보기 (PDF) - Unspecified
부품명
상세내역
제조사
GL3210 Datasheet PDF : 2 Pages
| |||
General Surface Preparation
All surfaces must be sound, dry, clean and free
of oil, grease, dirt, mildew, form release agents,
curing compounds, loose and flaking paint and
other foreign substances.
NEW SURFACES: Concrete, Masonry and
Plaster - Cure at least three days before painting,
poured in place concrete must cure for at least seven
days. pH must be 13.0 or lower. Roughen slick
poured or precast concrete by acid etching or sand-
sweeping. Follow acid manufacturer’s application and
safety instructions. Rinse thoroughly with water and
allow to dry. Must be internally dry. Remove loose
aggregate. Prime concrete and plaster with this
product. Fill masonry block with latex filler 3010.
Drywall - Remove sanding dust. Prime with this
Directions For Use
product. Wood - Interior, sand smooth. Dust clean.
Prime with this product. Exterior, counter sink nails.
Caulk with latex-type caulk. Prime with this product.
Steel - Prime steel with waterborne metal primer or
solventborne metal primer. Galvanized Metal and
Aluminum - Prime bare galvanized metal and
aluminum with this product.
PREVIOUSLY PAINTED SURFACES: Wash to
remove contaminants. Rinse thoroughly with water
and allow to dry. Sanding not required if the surface
is properly and thoroughly cleaned (scuff sanding is
required only on glossy, hard, slick or dense surfaces
which are subject to high levels of moisture). Remove
loose paint. Prime bare areas with primer specified
under NEW SURFACES.
TINTING: May be tinted with up to two oz/gal of
universal colorants.
APPLICATION: Mix thoroughly before use. May
be applied by brush, roller or spray. Brushing is the
preferred method of application over chalky
substrates. For spray application, use a .015” tip.
Seals water stains, inks, crayon, ballpoint pen marks,
lipstick, bleeding paints, knots, sap streaks, smoke
stains. Some stains may require a second coat.
Some highly water sensitive stains may require the
application of solventborne Stain JAMMER 1110 for
best results. If painting will be interrupted for more
than 15 minutes, keep brushes and rollers wet by
wrapping them with tinfoil or plastic wrap. This will
prevent the paint from drying in the equipment and
will make clean up much easier when the job is
finished. For exterior applications, stop painting at
least two hours before you expect heavy dew, rain,
or temperatures below 45°F (7°C).
SPREAD RATE: Apply at 300-450 sq ft/gal
(7-11 m2/L). Actual coverage may vary depending
on substrate and application method.
DRYING TIME: At 77°F (25°C) and 50% R.H., dries
to touch in 30 minutes and to recoat in one hour.
For maximum stain resistance, allow four hours
before topcoating. Low temperature, high humidity,
thick films or poor ventilation will increase these
times.
CLEAN-UP: Clean spatter and equipment
immediately with warm, soapy water.
Precautions
WARNING! CAUSES EYE BURNS. CAUSES SKIN AND RESPIRATORY TRACT IRRITATION. HARMFUL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL
WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS.
CONTAINS CRYSTALLINE SILICA WHICH CAN CAUSE LUNG CANCER AND OTHER LUNG DAMAGE IF INHALED. OVEREXPOSURE MAY CAUSE LIVER,
KIDNEY, BLOOD DAMAGE. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN. NOTICE: Products in this series may
contain solvents. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system
damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency information call (800)
545-2643. For additional safety information, refer to the Material Safety Data Sheet for this product. If sanding is done, wear a dust mask to avoid
breathing of sanding dust. Do not breathe vapors or spray mist. If you experience eye watering, headaches, or dizziness, leave the area. If properly used, a
respirator may offer additional protection. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact,
wash off quickly with plenty of soap and water, remove contaminated clothing. For eye contact flush immediately with large amounts of water, for at least
15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort,
remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. KEEP FROM FREEZING Note: These warnings
encompass the product series. Prior to use, read and follow product specific MSDS and label information.
DS51-0699
Shipping
FREIGHT CLASSIFICATION:
Paint, Freezable
FLASH POINT:
None
PACKAGING:
1 quart (0.946 L)
1 gallon (3.785 L)
5 gallons (18.925 L)
The Glidden Company, 925 Euclid Ave., Cleveland, Ohio 44115 1-800-GLIDDEN
Page two: GL3210 - 11/99 No. 32916
LIMITATION OF LIABILITY To the best of our knowledge, the technical data contained herein are true and
accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to
conform to the specifications contained herein. WE MAKE NO OTHER WARRANTY OR GUARANTEE OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF
LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
Share Link: 