HIP6018B 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
HIP6018B Datasheet PDF : 15 Pages
| |||
HIP6018B
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+15V
PGOOD, RT, FAULT, and GATE Voltage . . GND - 0.3V to VCC + 0.3V
Input, Output or I/O Voltage . . . . . . . . . . . . . . . . . . GND -0.3V to 7V
Operating Conditions
Supply Voltage, VCC .
Ambient Temperature
......
Range.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
+12V ±10%
0oC to 70oC
Junction Temperature Range . . . . . . . . . . . . . . . . . . . 0oC to 125oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
Maximum Junction Temperature (Plastic Package) 150oC
Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. Refer to Figures 1, 2 and 3
PARAMETER
VCC SUPPLY CURRENT
Nominal Supply
POWER-ON RESET
Rising VCC Threshold
Falling VCC Threshold
Rising VIN2 Under-Voltage Threshold
VIN2 Under-Voltage Hysteresis
Rising VOCSET1 Threshold
OSCILLATOR
Free Running Frequency
Total Variation
Ramp Amplitude
REFERENCE AND DAC
DAC(VID0-VID4) Input Low Voltage
DAC(VID0-VID4) Input High Voltage
DACOUT Voltage Accuracy
Reference Voltage (Pin FB2 and FB3)
LINEAR REGULATOR
Regulation
Under-Voltage Level
Under-Voltage Hysteresis
Over-Current Protection
Over-Current Protection During Start-Up
LINEAR CONTROLLER
Regulation
Under-Voltage Level
Under-Voltage Hysteresis
Output Drive Current
DRIVE3 Source Current
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
ICC
UGATE1, DRIVE3, LGATE1, and VOUT2 Open
-
8
-
mA
VOCSET = 4.5V
VOCSET = 4.5V
8.6
- 10.4
V
8.2
- 10.2
V
2.45 2.55 2.65
V
-
100
-
mV
- 1.25 -
V
ΔVOSC
RT = OPEN
6kΩ < RT to GND < 200kΩ
RT = Open
185 200 215
-15
-
+15
-
1.9
-
kHz
%
VP-P
-
-
0.8
V
2.0
-
-
V
-1.0
-
+1.0
%
1.240 1.265 1.290
V
FB2UV
10mA < IVOUT2 < 150mA
FB2 Rising
-2.5
-
2.5
%
-
75
87
%
-
6
-
%
180 230
-
mA
560 700
-
mA
FB3UV
VSEN3 = DRIVE3, 0 < IDRIVE3 < 20mA
FB3 Rising
IDRIVE3
VIN2 - VOUT3 > 1.5V
VIN2 - DRIVE3 > 0.6V
-2.5
-
2.5
%
-
75
87
%
-
6
-
%
20 40
-
mA
20 40
-
mA
4
Share Link: 