HIP6018 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
HIP6018 Datasheet PDF : 14 Pages
| |||
HIP6018
MOSFET switching. The over-current function will trip at a peak
inductor current (IPEAK) determined by:
IPEAK = -I-O-----C----S----E-r--D-T---S--x--(--O-R----N-O---)--C----S----E----T-
OVER-CURRENT TRIP: VDS > VSET
(iD • rDS(ON) > IOCSET • ROCSET)
OCSET
IOCSET
200µA
VCC
DRIVE
OC1
+
-
OVER-
CURRENT1
PWM
HIP6018
GATE
CONTROL
UGATE
PHASE
VCC
LGATE
PGND
VIN = +5V
ROCSET
VSET +
ID
+
VDS
VPHASE = VIN - VDS
VOCSET = VIN - VSET
FIGURE 9. OVER-CURRENT DETECTION
The OC trip point varies with MOSFET’s temperature. To avoid
over-current tripping in the normal operating load range,
determine the ROCSET resistor from the equation above with:
1. The maximum rDS(ON) at the highest junction
temperature.
2. The minimum IOCSET from the specification table.
3. Determine IPEAK for IPEAK > IOUT(MAX) + (∆I)/2,
where ∆I is the output inductor ripple current.
For an equation for the output inductor ripple current see
the section under component guidelines titled ‘Output
Inductor Selection’.
OUT1 Voltage Program
The output voltage of the PWM converter is programmed to
discrete levels between 1.8VDC and 3.5VDC. This output is
designed to supply the microprocessor core voltage. The
voltage identification (VID) pins program an internal voltage
reference (DACOUT) through a TTL-compatible 5-bit
digital-to-analog converter. The level of DACOUT also sets
the PGOOD and OVP thresholds. Table 1 specifies the
DACOUT voltage for the different combinations of
connections on the VID pins. The VID pins can be left open
for a logic 1 input, because they are internally pulled up to
+5V by a 10µA (typically) current source. Changing the VID
inputs during operation is not recommended. The sudden
change in the resulting reference voltage could toggle the
PGOOD signal and exercise the over-voltage protection. All
VID pin combinations resulting in an INHIBIT disable the IC
and the open-collector at the PGOOD pin.
TABLE 1. VOUT1 VOLTAGE PROGRAM
VID4
PIN NAME
VID3
VID2
VID1
VID0
NOMINAL
OUT1
VOLTAGE
DACOUT
0
1
X
X
X
INHIBIT
0
0
1
1
X
INHIBIT
0
0
1
0
1
1.80
0
0
1
0
0
1.85
0
0
0
1
1
1.90
0
0
0
1
0
1.95
0
0
0
0
1
2.00
0
0
0
0
0
2.05
1
1
1
1
1
INHIBIT
1
1
1
1
0
2.1
1
1
1
0
1
2.2
1
1
1
0
0
2.3
1
1
0
1
1
2.4
1
1
0
1
0
2.5
1
1
0
0
1
2.6
1
1
0
0
0
2.7
1
0
1
1
1
2.8
1
0
1
1
0
2.9
1
0
1
0
1
3.0
1
0
1
0
0
3.1
1
0
0
1
1
3.2
1
0
0
1
0
3.3
1
0
0
0
1
3.4
1
0
0
0
0
3.5
NOTE: 0 = connected to GND or VSS, 1 = open or connected to 5V
through pull-up resistors, X = don’t care
Application Guidelines
Soft-Start Interval
Initially, the soft-start function clamps the error amplifier’s
output of the PWM converter. After the output voltage
increases to approximately 80% of the set value, the
reference input of the error amplifier is clamped to a voltage
proportional to the SS pin voltage. Both linear outputs follow
a similar start-up sequence. The resulting output voltage
sequence is shown in Figure 6.
2-232
Share Link: 