HSSR-8060 데이터 시트보기 (PDF) - HP => Agilent Technologies
부품명
상세내역
제조사
HSSR-8060 Datasheet PDF : 13 Pages
| |||
Switching Specifications
For -40°C ≤ TA ≤ +85°C with Connection A, unless otherwise specified. All Typicals at TA = 25°C.
Parameter Symbol Min. Typ. Max. Units
Test Conditions
Fig. Notes
Turn On Time
tON
0.93 1.4 ms IF = 10 mA, VDD = 60 V,
IO = 750 mA, TA = 25°C
1.8 ms IF = 10 mA, VDD = 55 V,
IO = 750 mA
2,8, 7
9,10,
20,21
Turn Off Time
tOFF
0.013 0.1
ms IF = 10 mA, VDD = 60 V,
IO = 750 mA, TA = 25°C
2, 8,
11, 12,
0.1 ms IF = 10 mA, VDD = 55 V,
IO = 750 mA
20,21
Output
Transient
Rejection
|dVO/dt| 1000
V/µs V(peak) = 60 V, RM ≥ 1 MΩ,
16
CM = 1000 pF, TA = 25°C
Input-Output
Transient
Rejection
|dVI-O/dt| 2500
V/µs VDD = 5 V, VI-O(peak) = 1000 V, 17
RL = 1 kΩ, CL = 25 pF,
TA = 25°C
Package Characteristics
For 0°C ≤ TA ≤ 70°C, unless otherwise specified. All typicals at TA = 25°C.
Parameter Symbol Min. Typ. Max. Units
Test Conditions
Fig. Notes
Input-Output
VISO 2500
Momentary With-
stand Voltage*
V rms RH ≤ 50%, t = 1 min, TA = 25°C
5,6
Resistance
RI-O
100
GΩ VI-O = 500 Vdc, t = 1 min,
5
Input-Output
RH = 45%
Capacitance
CI-O
1.0
pF VI-O = 0 V, f = 1 MHz
5
Input-Output
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. The case temperature, TC, is measured
at the center of the bottom of the
package.
2. For derating, see Figure 4. The output
power PO derating curve is obtained
when the part is handling the maximum
average output current IO as shown in
Figure 3.
3. During the pulsed RON measurement (IO
duration ≤ 30 ms), ambient (TA) and
case temperature (TC) are equal.
4. VOS is a function of IF, and is defined
between pins 4 and 6, with pin 4 as the
reference. VOS must be measured in a
stable ambient (free of temperature
gradients).
5. Device considered a two terminal
device: pins 1, 2, and 3 shorted
together and pins 4, 5, and 6 shorted
together.
6. This is a momentary withstand proof
test. These parts are 100% tested in
production at 3000 V rms, one second.
7. For a faster turn-on time, the optional
peaking circuit shown in Figure 2 may
be implemented.
1-447
Share Link: 