HT46R321 데이터 시트보기 (PDF) - Holtek Semiconductor

부품명

상세내역

제조사

HT46R321

A/D Type 8-Bit OTP MCU with OPA and 8
4 LED Driver

Holtek Semiconductor 

HT46R321

Status Register - STATUS

This 8-bit register contains the zero flag (Z), carry flag

(C), auxiliary carry flag (AC), overflow flag (OV), power

down flag (PDF), and watchdog time-out flag (TO). It

also records the status information and controls the op-

eration sequence.

With the exception of the TO and PDF flags, bits in

the status register can be altered by instructions like

most other registers. Any data written into the status

register will not change the TO or PDF flag. In addi-

tion operations related to the status register may give

different results from those intended. The TO flag

can be affected only by system power-up, a WDT

time-out or executing the ²CLR WDT² or ²HALT² in-

struction. The PDF flag can be affected only by exe-

cuting the ²HALT² or ²CLR WDT² instruction or a

system power-up.

The Z, OV, AC and C flags generally reflect the status of

the latest operations.

In addition, on entering the interrupt sequence or exe-

cuting the subroutine call, the status register will not be

pushed onto the stack automatically. If the contents of

the status are important and if the subroutine can cor-

rupt the status register, precautions must be taken to

save it properly.

Interrupt

The devices provide an external interrupt, an internal

timer/event counter interrupt and an A/D converter inter-

rupt. The Interrupt Control Register, INTC, contains the

interrupt control bits to set the enable or disable and the

interrupt request flags.

Once an interrupt subroutine is serviced, all the other in-

terrupts will be blocked by clearing the EMI bit. This

scheme may prevent any further interrupt nesting. Other

interrupt requests may happen during this interval but

only the interrupt request flag is recorded. If a certain in-

terrupt requires servicing within the service routine, the

EMI bit and the corresponding bit in INTC may be set to

allow interrupt nesting. If the stack is full, the interrupt re-

quest will not be acknowledged, even if the related inter-

rupt is enabled, until the stack pointer is decremented. If

immediate service is desired, the stack must be pre-

vented from becoming full.

Bit No.

0

1

2

3

4

5

6, 7

Label

C

AC

Z

OV

PDF

TO

¾

Function

C is set if an operation results in a carry during an addition operation or if a borrow does not

take place during a subtraction operation, otherwise C is cleared. C is also affected by a ro-

tate through carry instruction.

AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from

the high nibble into the low nibble in subtraction, otherwise AC is cleared.

Z is set if the result of an arithmetic or logic operation is zero, otherwise Z is cleared.

OV is set if an operation results in a carry into the highest-order bit but not a carry out of the

highest-order bit, or vice versa, otherwise OV is cleared.

PDF is cleared by a system power-up or executing the ²CLR WDT² instruction. PDF is set by

executing the ²HALT² instruction.

TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction. TO

is set by a WDT time-out.

Unused bit, read as ²0²

Status (0AH) Register

Bit No.

0

1

2

3

4

5

6

7

Label

EMI

EEI

ETI

EADI

EIF

TF

ADF

¾

Function

Controls the master (global) interrupt (1=enabled; 0=disabled)

Controls the external interrupt (1=enabled; 0=disabled)

Controls the Timer/Event Counter interrupt (1=enabled; 0=disabled)

Controls the A/D converter interrupt (1=enabled; 0=disabled)

External interrupt request flag (1=active; 0=inactive)

Internal Timer/Event Counter request flag (1=active; 0=inactive)

End of A/D conversion interrupt request flag (1=active; 0=inactive)

Unused bit, read as ²0²

INTC (0BH) Register

Rev. 1.00

10

August 3, 2007

Share Link: