DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

HT82V842 데이터 시트보기 (PDF) - Holtek Semiconductor

부품명
상세내역
제조사
HT82V842
Holtek
Holtek Semiconductor Holtek
HT82V842 Datasheet PDF : 18 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
HT82V842
A/D Converter Output Code (Mode 1 Register D5=1)
The format of an ADC digital output is a straight binary.
When in the input zero reference voltage, the output
code will be all zero and when the input is a full scale
voltage, the output code will be all one.
Clock, Pipeline Delay, Digital Data Output Timing
The ADCK input is used for an A/D conversion. The
ADC input signal is sampled at the falling edge of the
ADCK input and 10 bits parallel data is output at the ris-
ing edge of the ADCK input after a 5.5 clock of pipeline
delay.
High-Z Control of ADC Digital Output
ADC digital outputs become High-Z under the following
conditions:
· Set the ADC output bit to one. (Mode 1 register D2=1)
· Set the STBY pin to low
· Set the power control bit to one (Mode 1 register
D0=1)
Digital Output Code
A/D Input MSB
LSB
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Full Scale
1
1
1
1
1
1
1
1
1
1
:
:
:
:
:
:
:
:
:
:
:
:
1
0
0
0
0
0
0
0
0
0
:
0
1
1
1
1
1
1
1
1
1
:
:
:
:
:
:
:
:
:
:
:
Zero Scale
0
0
0
0
0
0
0
0
0
0
ADC Data Output (Coding: Straight Binary)
Miscellaneous Function
(ADC Direct Input, ADIN Mode)
The direct input path to the ADC or the PGA is achieved
by means of a register setting. The selectable paths are
as follows:
· Function disable (default, Mode 1 register D5=0,
D4=0)
· ADIN input to the PGA (Mode 1 register D5=0, D4=1)
· ADIN input to the PGA (Mode 1 register D5=1,
D4=Don¢t care)
The BLK, SHD and SHR inputs are ignored at the ADIN
mode.
Power Down Mode
The power down mode can be set either by register set-
ting or by the STBY pin.
Monitor Output
When setting Mode 2 (D1 and D0), the signal from
MONOUT is selectable. The alternatives are OFF, CDS
output, PGA output or REFIN/CCDIN output. The
MONOUT pin gain is fixed to 0dB regardless of the gain
control register setting when the CDS output is selected.
The MONOUT level becomes VCOM at zero reference
level. The signals are output in reverse for the CCD in-
put.
Polarity Inversion
The following input polarities can be inverted by register
setting:
· ADCK (A/D converter sampling clock, Mode 1 register
D6)
· SHR and SHD (CDS sampling clock, Mode 2 register
D3 and D2)
· BLK, OBP, CCDCLP and ADCLP (Mode 2 register D3
and D2)
Data Output Clock
The ADCK input or the OUTCK input is selectable as an
ADC data output clock.
Serial Interface Circuit
The internal registers of the HT82V842 are controlled by
a 3-wire serial interface. The data is a 16-bit length se-
rial data that consists of a 2-bit operation code, 4 bits ad-
dress and 10 bits data. Each bit is fetched at the rising
edge of the CS input. Keep CS to high when not access
HT82V842. It is prohibited to write to a non-defined ad-
dress. When a data length is below 16 bits, the data is
not executed.
Registers
The HT82V842 has 10 bits´7 registers that control the
operations. All registers are write only, the serial regis-
ters are written by the serial interface.
Rev. 1.00
7
July 15, 2004

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]