IDT54FCT162841AT 데이터 시트보기 (PDF) - Integrated Device Technology
부품명
상세내역
제조사
IDT54FCT162841AT Datasheet PDF : 9 Pages
| |||
IDT54/74FCT16841AT/BT/CT/ET, 162841AT/BT/CT/ET
FAST CMOS 20-BIT TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = –40°C to +85°C, VCC = 5.0V ± 10%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%
Symbol
VIH
Parameter
Input HIGH Level
Test Conditions(1)
Guaranteed Logic HIGH Level
Min. Typ.(2) Max. Unit
2.0 —
—
V
VIL
II H
II L
IOZH
IOZL
Input LOW Level
Input HIGH Current (Input pins)(5)
Input HIGH Current (I/O pins)(5)
Input LOW Current (Input pins)(5)
Input LOW Current (I/O pins)(5)
High Impedance Output Current
(3-State Output pins)(5)
Guaranteed Logic LOW Level
VCC = Max.
VI = VCC
VI = GND
VCC = Max.
VO = 2.7V
VO = 0.5V
—
— 0.8
V
—
—
±1 µA
—
—
±1
—
—
±1
—
—
±1
—
—
±1 µA
—
—
±1
VIK
Clamp Diode Voltage
IOS
Short Circuit Current
VH
Input Hysteresis
VCC = Min., IIN = –18mA
VCC = Max., VO = GND(3)
—
— –0.7 –1.2 V
–80 –140 –225 mA
— 100 — mV
ICCL
ICCH
ICCZ
Quiescent Power Supply Current VCC = Max., VIN = GND or VCC
—
5
500 µA
2556 lnk 05
OUTPUT DRIVE CHARACTERISTICS FOR FCT16841T
Symbol
IO
Parameter
Output Drive Current
Test Conditions(1)
VCC = Max., VO = 2.5V(3)
Min. Typ.(2) Max. Unit
–50 — –180 mA
VOH
Output HIGH Voltage
VCC = Min.
IOH = –3mA
2.5 3.5 —
V
VOL
IOFF
VIN = VIH or VIL
IOH = –12mA MIL.
2.4
IOH = –15mA COM'L.
IOH = –24mA MIL.
2.0
IOH = –32mA COM'L.(4)
Output LOW Voltage
VCC = Min.
IOL = 48mA MIL.
—
VIN = VIH or VIL
IOL = 64mA COM'L.
Input/Output Power Off Leakage(5) VCC = 0V, VIN or VO ≤ 4.5V
—
3.5 —
V
3.0 —
V
0.2 0.55 V
—
±1
µA
2556 lnk 06
OUTPUT DRIVE CHARACTERISTICS FOR FCT162841T
Symbol
IODL
Parameter
Output LOW Current
Test Conditions(1)
VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V(3)
Min. Typ.(2) Max. Unit
60 115 200 mA
IODH
Output HIGH Current
VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V(3)
–60 –115 –200 mA
VOH
Output HIGH Voltage
VCC = Min.
VIN = VIH or VIL
IOH = –16mA MIL.
2.4 3.3 —
V
IOH = –24mA COM'L.
VOL
Output LOW Voltage
VCC = Min.
VIN = VIH or VIL
IOL = 16mA MIL.
IOL = 24mA COM'L.
— 0.3 0.55 V
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. The test limit for this parameter is ± 5µA at TA = –55°C.
2556 lnk 07
5.18
4
Share Link: 