DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

IDT54FCT164245TPV 데이터 시트보기 (PDF) - Integrated Device Technology

부품명
상세내역
제조사
IDT54FCT164245TPV
IDT
Integrated Device Technology IDT
IDT54FCT164245TPV Datasheet PDF : 9 Pages
1 2 3 4 5 6 7 8 9
IDT54/74FCT164245T
FAST CMOS 16-BIT BIDIRECTIONAL 3.3V-TO-5V TRANSLATOR
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (B PORT - 5V)
Following Conditions Apply Unless Otherwise Specified:
VCC1 = 5V ± 10%, VCC2 = 2.7V to 3.6V; Commercial: TA = –40°C to +85°C, Military: TA = –55°C to +125°C,
Symbol
VIH
VIL
II H
Parameter
Input HIGH Level
(Input and I/O pins)
Input LOW Level
(Input and I/O pins)
Input HIGH Current (Input pins)
Test Conditions(1)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
VCC1 = Max.
VI = VCC1
Min. Typ.(2) Max. Unit
2.0 — 5.5
V
–0.5 0.8
V
±5
µA
Input HIGH Current (I/O pins)
VCC2 = Max.
±15
II L
Input LOW Current (Input pins)
VI = GND
±5
Input LOW Current (I/O pins)
±15
VIK
Clamp Diode Voltage
VCC1 = Min., IIN = –18mA
0.7 1.2 V
VOH
Output HIGH Voltage
VCC1 = Min.
VCC2 = Min.
VIN = VIH or VIL
IOH = –3mA
2.5 3.5 —
V
IOH = –12mA MIL.
2.4 3.5 —
IOH = –15mA COM'L.
IOH = –24mA MIL.
2.0 3.0 —
IOH = –32mA COM'L.(5)
VOL
Output LOW Voltage
VCC1 = Min.,
VCC2 = Min.
VIN = VIH or VIL
IOL = 48mA MIL.
IOL = 64mA COM'L.
— 0.2 0.55 V
IOFF
Input/Output Power Off Leakage VCC1 = 0V, VCC2 = 0V, VIN or VO 4.5V
±100 µA
IOS
Short Circuit Current(4)
VCC1 = Max., VCC2 = Max., VO = GND(3)
–80 140 225 mA
IO
Output Drive Current
VCC1 = Max., VCC2 = Max., VO = 2.5V(3)
–50 –75 180 mA
VH
Input Hysteresis
— 150
mV
ICC1L
Quiescent Power Supply Current VCC1 = Max., VIN = GND or VCC2
— 0.08 1.5
ICC1H
VCC2 = Max.
ICC1Z
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC1 = 5.0V, VCC2 = 3.3V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. This parameter is guaranteed but not tested.
5 Duration of the condition can not exceed one second.
mA
2555 tbl 06
8.16
5

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]