ISL8200AMIRZ 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
ISL8200AMIRZ Datasheet PDF : 24 Pages
| |||
ISL8200AM
Absolute Maximum Ratings
Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +27V
Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.0V
Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
BOOT/UGATE Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +36V
Phase Voltage, VPHASE . . . . . . . . . . . . . . . . . . . VBOOT - 7V to VBOOT + 0.3V
BOOT to PHASE Voltage,
VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
Input, Output or I/O Voltage . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
ESD Rating
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 200V
Charge Device Model (Tested per JESD22-C101C). . . . . . . . . . . . . . . 1kV
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
QFN Package (Notes 4, 5) . . . . . . . . . . . . . .
13
2.0
Maximum Storage Temperature Range . . . . . . . . . . . . . .-55°C to +150°C
Recommended Operating Conditions
Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 20V
Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V to 5.6V
Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V to 5.6V
Boot to Phase Voltage
VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <6V
Industrial Ambient Temperature Range . . . . . . . . . . . . . . . -40°C to +85°C
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board (i.e., 4-layer type without thermal vias -
see tech brief TB379) per JEDEC standards except that the top and bottom layers assume solid plains.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Boldface limits apply over the operating temperature range, -40°C to +85°C.
PARAMETER
VCC SUPPLY CURRENT
Nominal Supply VIN Current
Nominal Supply VIN Current
Shutdown Supply VCC Current
INTERNAL LINEAR REGULATOR
Maximum Current
Saturated Equivalent Impedance
PVCC Voltage Level (Note 7)
POWER-ON RESET (Note 7)
Rising VCC Threshold
Falling VCC Threshold
Rising PVCC Threshold
Falling PVCC Threshold
System Soft-start Delay
ENABLE (Note 7)
Turn-On Threshold Voltage
Hysteresis Sink Current
Undervoltage Lockout Hysteresis
Sink Current
Sink Impedance
OSCILLATOR
Oscillator Frequency
Total Variation (Note 7)
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
(Note 7) (Note 6) (Note 7) UNITS
IQ_VIN
IQ_VIN
IVCC
IPVCC
RLDO
PVCC
tSS_DLY
PVIN = VIN = 20V; No Load; FSW = 700kHz
PVIN = VIN = 4.5V; No Load; FSW = 700kHz
EN = 0V, VCC = 2.97V
PVCC = 4V to 5.6V
P-Channel MOSFET (VIN = 5V)
IPVCC = 0mA, VIN = 12V
5.15
After PLL, VCC, and PVCC PORs, and EN above
their thresholds
36
27
9
320
1
5.4
2.85
2.65
2.85
2.65
384
mA
mA
mA
mA
Ω
5.60
V
2.97
2.75
2.97
2.75
V
V
V
V
Cycles
IEN_HYS
VEN_HYS
IEN_SINK
REN_SINK
VEN_RTH = 10.6V; VEN_FTH = 9V
RUP = 53.6kΩ, RDOWN = 5.23kΩ
VEN = 1V
VEN = 1V
FOSC
RFS = 59kΩ; Figure 34
VCC = 5V;
0.75
0.8
0.86
V
21
30
35
µA
1.6
V
15.4
mA
64
Ω
700
kHz
-9
+9
%
7
FN8271.2
September 13, 2012
Share Link: 