ISL8200M_10 데이터 시트보기 (PDF) - Intersil

부품명

상세내역

제조사

ISL8200M_10

Complete Current Share 10A DC/DC Power Module

Intersil 

ISL8200M

Absolute Maximum Ratings

Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . -0.3V to +27V

Driver Bias Voltage, PVCC . . . . . . . . . . . . . . -0.3V to +6.5V

Signal Bias Voltage, VCC . . . . . . . . . . . . . . . -0.3V to +6.5V

BOOT/UGATE Voltage, VBOOT. . . . . . . . . . . . . -0.3V to +36V

Phase Voltage, VPHASE . . . . . . . VBOOT - 7V to VBOOT + 0.3V

BOOT to PHASE Voltage,

VBOOT - VPHASE . . . . . . . . . . . . . . . .-0.3V to VCC + 0.3V

Input, Output or I/O Voltage . . . . . . . . .-0.3V to VCC + 0.3V

ESD Rating

Human Body Model (Tested per JESD22-A114E) . . . . . 2kV

Machine Model (Tested per JESD22-A115-A) . . . . . . . 200V

Charge Device Model (Tested per JESD22-C101C) . . . . 1kV

Latch Up (Tested per JESD-78B; Class 2, Level A) . . . 100mA

Thermal Information

Thermal Resistance (Typical)

θJA (°C/W) θJC (°C/W)

QFN Package (Notes 4, 5) . . . . . . . 13

2.0

Maximum Storage Temperature Range . . . -40°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

Recommended Operating Conditions

Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . . . .3V to 20V

Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . 3V to 5.6V

Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . 3V to 5.6V

Boot to Phase Voltage (Overcharged),

VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . .<6V

Commercial Ambient Temperature Range. . . . . 0°C to +70°C

Industrial Ambient Temperature Range . . . . -40°C to +85°C

Junction Temperature Range . . . . . . . . . . -40°C to +125°C

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact

product reliability and result in failures not covered by warranty.

NOTES:

4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach”

features. See Tech Brief TB379.

5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.

6. Parameters with TYP limits are not production tested, unless otherwise specified.

7. Parameters are 100% tested for internal IC prior to module assembly.

Electrical Specifications

Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.

Temperature limits established by characterization and are not production tested. Boldface

limits apply over the operating temperature range, -40°C to +85°C.

PARAMETER

SYMBOL

TEST CONDITIONS

TYP

MIN (Note 6)

MAX

UNITS

VCC SUPPLY CURRENT

Nominal Supply VIN Current

IQ_VIN

Nominal Supply VIN Current

IQ_VIN

Shutdown Supply VCC Current

IVCC

INTERNAL LINEAR REGULATOR

PVIN = VIN = 20V; No Load;

FSW = 700kHz

PVIN = VIN = 4.5V; No Load;

FSW = 700kHz

EN = 0V, VCC = 2.97V

36

mA

27

mA

9

mA

Maximum Current

IPVCC

PVCC = 4V TO 5.6V

PVCC = 3V TO 4V

250

mA

150

mA

Saturated Equivalent

Impedance

RLDO

P-Channel MOSFET (VIN = 5V)

1

Ω

PVCC Voltage Level (Note 7)

POWER-ON RESET (Note 7)

PVCC

IPVCC = 0mA to 250mA

5.1

5.4

5.6

V

Rising VCC Threshold

2.85

2.97

V

Falling VCC Threshold

2.65

2.75

V

Rising PVCC Threshold

0°C to +70°C

2.85

2.97

V

-40°C to +85°C

2.85

3.05

Falling PVCC Threshold

2.65

2.75

V

System Soft-start Delay

tSS_DLY After PLL, VCC, and PVCC PORs, and EN

384

above their thresholds

Cycles

ENABLE (Note 7)

Maximum Input Voltage

VEN

Turn-On Threshold Voltage

VCC

V

0.75

0.8

0.86

V

Hysteresis Sink Current

IEN_HYS

25

30

35

µA

7

FN6727.1

February 26, 2010

Share Link: