ISL84521IB(2003) 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
ISL84521IB Datasheet PDF : 12 Pages
| |||
ISL84521, ISL84522, ISL84523
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 to 0.3V
All Other Pins (Note 3) . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 10mA
Peak Current, IN, NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 20mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . > 2kV
Operating Conditions
Temperature Range
ISL8452XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Thermal Information
Thermal Resistance (Typical, Note 4)
θJA (oC/W)
16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . .
115
16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC
Moisture Sensitivity (See Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Storage Temperature Range. . . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on NC, NO, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current ratings.
4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications +5V Supply Test Conditions: VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 6)
(NOTE 6)
(oC)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
V-
ON Resistance, RON
VS = ±5V, ICOM = 1.0mA, VNO or VNC = ±3V (Figure 5) 25
-
Full
-
-
V+
V
65
100
Ω
-
125
Ω
RON Matching Between Channels, VS = ±5V, ICOM = 1.0mA, VNO or VNC = ±3V
∆RON
25
-
1
4
Ω
Full
-
-
6
Ω
RON Flatness, RFLAT(ON)
VS = ±5V, ICOM = 1.0mA, VNO or VNC = ±3V (Note 8) 25
-
Full
-
7
12
Ω
-
15
Ω
NO or NC OFF Leakage Current,
INO(OFF) or INC(OFF)
VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V
(Note 7)
25
-1
0.01
Full
-10
-
1
nA
10
nA
COM OFF Leakage Current,
ICOM(OFF)
VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V
(Note 7)
25
-1
0.01
Full
-10
-
1
nA
10
nA
COM ON Leakage Current,
ICOM(ON)
VS = ±5.5V, VCOM = VNO or VNC = ±4.5V (Note 7)
25
-2
Full
-20
0.01
-
2
nA
20
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINH, IINL
DYNAMIC CHARACTERISTICS
VS = ±5.5V, VIN = 0V or V+
Full
-
1.6
2.4
V
Full
0.8
1.6
-
V
Full
-1
0.03
1
µA
Turn-ON Time, tON
VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, 25
-
VIN = 0 to 3V (Figure 1)
Full
-
45
80
ns
-
100
ns
Turn-OFF Time, tOFF
VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, 25
-
VIN = 0 to 3V (Figure 1)
Full
-
15
30
ns
-
40
ns
Break-Before-Make Time Delay
VS = ±5.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF, 25
5
20
-
ns
(ISL84523), tD
VIN = 0 to 3V (Figure 3)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω (Figure 2)
25
-
1
5
pC
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (Figure 7)
25
-
2
-
pF
COM OFF Capacitance,
CCOM(OFF)
f = 1MHz, VNO or VNC = VCOM = 0V (Figure 7)
25
-
2
-
pF
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (Figure 7)
25
-
5
-
pF
3
Share Link: 