LT1206
ELECTRICAL CHARACTERISTICS VCM = 0, ±5V ≤ VS ≤ ±15V, pulse tested, VS/D = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN TYP MAX UNITS
CMRR
PSRR
Common-Mode Rejection Ratio
Inverting Input Current
Common-Mode Rejection
Power Supply Rejection Ratio
Noninverting Input Current
Power Supply Rejection
VS = ±15V, VCM = ±12V
VS = ±5V, VCM = ±2V
VS = ±15V, VCM = ±12V
VS = ±5V, VCM = ±2V
VS = ±5V to ±15V
VS = ±5V to ±15V
q
55
62
dB
q
50
60
dB
q
0.1
10
µA / V
q
0.1
10
µA / V
q
60
77
dB
q
30
500
nA / V
Inverting Input Current
Power Supply Rejection
VS = ±5V to ±15V
q
0.7
5
µA / V
AV
Large-Signal Voltage Gain
ROL
Transresistance, ∆VOUT/∆IIN–
VOUT
Maximum Output Voltage Swing
IOUT
Maximum Output Current
IS
Supply Current
VS = ±15V, VOUT = ±10V, RL = 50Ω
VS = ±5V, VOUT = ±2V, RL = 25Ω
VS = ±15V, VOUT = ±10V, RL = 50Ω
VS = ±5V, VOUT = ±2V, RL = 25Ω
VS = ±15V, RL = 50Ω, TA = 25°C
VS = ±5V, RL = 25Ω, TA = 25°C
RL = 1Ω
VS = ±15V, VS/D = 0V, TA = 25°C
q
55
71
dB
q
55
68
dB
q 100
260
kΩ
q
75
200
kΩ
±11.5 ±12.5
V
q ±10.0
V
±2.5 ±3.0
V
q ±2.0
V
q 250
500
1200
mA
20
30
mA
q
35
mA
Supply Current, RS/D = 51k (Note 3)
VS = ±15V, TA = 25°C
12
17
mA
Positive Supply Current, Shutdown
VS = ±15V, VS/D = 15V
q
200
µA
Output Leakage Current, Shutdown
VS = ±15V, VS/D = 15V
q
10
µA
SR
Slew Rate (Note 4)
AV = 2, TA = 25°C
400 900
V/µs
Differential Gain (Note 5)
VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω
0.02
%
Differential Phase (Note 5)
VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω
0.17
DEG
BW
Small-Signal Bandwidth
VS = ±15V, Peaking ≤ 0.5dB
RF = RG = 620Ω, RL = 100Ω
60
MHz
VS = ±15V, Peaking ≤ 0.5dB
RF = RG = 649Ω, RL = 50Ω
52
MHz
VS = ±15V, Peaking ≤ 0.5dB
RF = RG = 698Ω, RL = 30Ω
43
MHz
VS = ±15V, Peaking ≤ 0.5dB
RF = RG = 825Ω, RL = 10Ω
27
MHz
The q denotes specifications which apply for 0°C ≤ TA ≤ 70°C.
Note 1: Applies to short circuits to ground only. A short circuit between
the output and either supply may permanently damage the part when
operated on supplies greater than ±10V.
Note 2: Commercial grade parts are designed to operate over the
temperature range of – 40°C to 85°C but are neither tested nor guaranteed
beyond 0°C to 70°C. Industrial grade parts tested over – 40°C to 85°C are
available on special request. Consult factory.
Note 3: RS/D is connected between the shutdown pin and ground.
Note 4: Slew rate is measured at ±5V on a ±10V output signal while
operating on ±15V supplies with RF = 1.5k, RG = 1.5k and RL = 400Ω.
Note 5: NTSC composite video with an output level of 2V.
3