LT6203IMS8(2002) 데이터 시트보기 (PDF) - Linear Technology
부품명
상세내역
제조사
LT6203IMS8
(Rev.:2002)
(Rev.:2002)
Linear Technology
LT6203IMS8 Datasheet PDF : 24 Pages
| |||
LT6202/LT6203/LT6204
ELECTRICAL CHARACTERISTICS The q denotes the specifications which apply over –40°C < TA < 85°C
temperature range. VS = ±5V; VCM = VOUT = 0V, unless otherwise noted. (Note 5)
SYMBOL
VOS TC
IB
∆IB
IOS
AVOL
CMRR
PSRR
VOL
VOH
ISC
IS
GBW
SR
FPBW
PARAMETER
Input Offset Voltage Drift (Note 9)
Input Offset Voltage Match
(Channel-to-Channel) (Note 6)
Input Bias Current
IB Shift
IB Match (Channel-to-Channel) (Note 6)
Input Offset Current
Large Signal Gain
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 6)
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 6)
Output Voltage Swing LOW Saturation
(Note 8)
Output Voltage Swing HIGH Saturation
(Note 8)
Short-Circuit Current
Supply Current per Amp
Gain Bandwidth Product
Slew Rate
Full Power Bandwidth (Note 10)
CONDITIONS
VCM = Half Supply
VCM = 0V
VCM = V– to V+
VCM
VCM
=
=
Half
V+
Supply
VCM = V–
VCM = V– to V+
VCM
VCM
=
=
Half
V+
Supply
VCM = V–
VO = ±4.5V, RL = 1k
VO = ±1.5V RL = 100
VCM = V– to V+
VCM = –2V to 2V
VCM = –2V to 2V
VS = ±1.5V to ±5V
VS = ±1.5V to ±5V
No Load
ISINK = 5mA
ISINK = 15mA
No Load
ISOURCE = 5mA
ISOURCE = 15mA
Frequency = 1MHz
AV = –1, RL = 1k, VO = 4V
VOUT = 3VP-P
MIN TYP MAX UNITS
q
7.5
24
µV/°C
q
0.3
1.0
mV
q
0.6
2.5
mV
q –7.0 –1.4
µA
q
1.8
3.6
µA
q –10 –4.5
µA
q
5.4
13
µA
q
0.15
0.7
µA
q
0.15
1
µA
q
0.3
1.2
µA
q
0.5
1.6
µA
q 60
110
q 6.0
13
V/mV
V/mV
q 65
84
dB
q 80
95
dB
q 80
110
dB
q 60
70
dB
q 70
100
dB
q
7
75
mV
q
98
205
mV
q
260 500
mV
q
70
130
mV
q
130 250
mV
q
360 640
mV
q ±15
±25
mA
q
3.8
4.5
mA
q
90
MHz
q 13
18
V/µs
q 1.4
1.9
MHz
Note 1: Absolute maximum ratings are those values beyond which the life
of the device may be impaired.
Note 2: Inputs are protected by back-to-back diodes and diodes to each
supply. If the inputs are taken beyond the supplies or the differential input
voltage exceeds 0.7V, the input current must be limited to less than 40mA.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The LT6202C/LT6202I, LT6203C/LT6203I and LT6204C/LT6204I
are guaranteed functional over the temperature range of –40°C and 85°C.
Note 5: The LT6202C/LT6203C/LT6204C are guaranteed to meet specified
performance from 0°C to 70°C. The LT6202C/LT6203C/LT6204C are
designed, characterized and expected to meet specified performance from
–40°C to 85°C, but are not tested or QA sampled at these temperatures.
The LT6202I/LT6203I/LT6204I are guaranteed to meet specified
performance from –40°C to 85°C.
Note 6: Matching parameters are the difference between the two amplifiers
A and D and between B and C of the LT6204; between the two amplifiers
of the LT6203. CMRR and PSRR match are defined as follows: CMRR and
PSRR are measured in µV/V on the identical amplifiers. The difference is
calculated between the matching sides in µV/V. The result is converted to
dB.
Note 7: Minimum supply voltage is guaranteed by power supply rejection
ratio test.
Note 8: Output voltage swings are measured between the output and
power supply rails.
Note 9: This parameter is not 100% tested.
Note 10: Full-power bandwidth is calculated from the slew rate:
FPBW = SR/2πVP
Note 11: Differential gain and phase are measured using a Tektronix
TSG120YC/NTSC signal generator and a Tektronix 1780R Video
Measurement Set. The resolution of this equipment is 0.1% and 0.1°. Ten
identical amplifier stages were cascaded giving an effective resolution of
0.01% and 0.01°.
620234fa
9
Share Link: