LTM4601 데이터 시트보기 (PDF) - Linear Technology

부품명

상세내역

제조사

LTM4601

6A, 28VIN DC/DC µModule with PLL, Output Tracking and Margining

Linear Technology 

LTM4603HV

APPLICATIO S I FOR ATIO

The typical LTM4603HV application circuit is shown in

Figure 20. External component selection is primarily

determined by the maximum load current and output

voltage. Refer to Table 2 for specific external capacitor

requirements for a particular application.

VIN to VOUT Step-Down Ratios

There are restrictions in the maximum VIN and VOUT step

down ratio that can be achieved for a given input voltage.

These constraints are shown in the Typical Performance

Characteristics curves labeled VIN to VOUT Step-Down

Ratio. Note that additional thermal derating may apply. See

the Thermal Considerations and Output Current Derating

section of this data sheet.

Output Voltage Programming and Margining

The PWM controller has an internal 0.6V reference voltage.

As shown in the Block Diagram, a 1M and a 60.4k 0.5%

internal feedback resistor connects VOUT and VFB pins

together. The VOUT_LCL pin is connected between the 1M

and the 60.4k resistor. The 1M resistor is used to protect

against an output overvoltage condition if the VOUT_LCL

pin is not connected to the output, or if the remote sense

amplifier output is not connected to VOUT_LCL. The output

voltage will default to 0.6V. Adding a resistor RSET from

the VFB pin to SGND pin programs the output voltage:

VOUT

=

0.6V

60.4k + RSET

RSET

Table 1. Standard 1% Resistor Values

RSET

(kΩ)

Open

60.4

40.2 30.1 25.5

19.1

13.3

8.25

VOUT

(V)

0.6

1.2

1.5

1.8

2

2.5 3.3

5

The MPGM pin programs a current that when multiplied

by an internal 10k resistor sets up the 0.6V reference ±

offset for margining. A 1.18V reference divided by the

RPGM resistor on the MPGM pin programs the current.

Calculate VOUT(MARGIN):

VOUT(MARGIN)

=

%VOUT

100

•

VOUT

where %VOUT is the percentage of VOUT you want to margin,

and VOUT(MARGIN) is the margin quantity in volts:

RPGM

=

VOUT

0.6V

•

1.18V

VOUT(MARGIN)

• 10k

where RPGM is the resistor value to place on the MPGM

pin to ground.

The output margining will be ± margining of the value.

This is controlled by the MARG0 and MARG1 pins. See

the truth table below:

MARG0

LOW

LOW

HIGH

HIGH

MARG1

LOW

HIGH

LOW

HIGH

MODE

NO MARGIN

MARGIN UP

MARGIN DOWN

NO MARGIN

Input Capacitors

LTM4603HV module should be connected to a low AC

impedance DC source. Input capacitors are required to

be placed adjacent to the module. In Figure 20, the 10μF

ceramic input capacitors are selected for their ability to

handle the large RMS current into the converter. An input

bulk capacitor of 100μF is optional. This 100μF capacitor is

only needed if the input source impedance is compromised

by long inductive leads or traces.

For a buck converter, the switching duty-cycle can be

estimated as:

D = VOUT

VIN

Without considering the inductor current ripple, the RMS

current of the input capacitor can be estimated as:

( ) ICIN(RMS)

=

IOUT(MAX)

η%

•

D • 1– D

In the above equation, η% is the estimated efficiency of

the power module. CIN can be a switcher-rated electrolytic

aluminum capacitor, OS-CON capacitor or high volume

ceramic capacitor. Note the capacitor ripple current rat-

ings are often based on temperature and hours of life. This

makes it advisable to properly derate the input capacitor,

4603hvf

10

Share Link: