L8576B 데이터 시트보기 (PDF) - Agere -> LSI Corporation
부품명
상세내역
제조사
L8576B Datasheet PDF : 26 Pages
| |||
L8576B Dual Ringing SLIC
Data Sheet
May 2001
Pin Information (continued)
Table 1. Pin Descriptions (continued)
Pin,
Circuit
a
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
Pin,
Circuit
b
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Symbol
RNGNG
NSTAT
NDISC
RPWR
PT
PR
VITR
TG2
TG1
RTFLT
RTTH
DCOUT
IPROG
RCVP
RCVN
AGND
VCC
RRNG
Type
Iu
Ou
Iu
—
I/O
I/O
O
—
—
—
—
O
I
I
I
—
—
—
Name/Function
Ringing Input. Refer to Operating States section. A pull-up device is
included.
Loop Detector Output/Ring Trip Detector Output. When low, this lead indi-
cates an off-hook condition. When in ringing mode, a low output on this lead
indicates a ring trip. A pull-up device is included.
Disconnect Input. Refer to Operating States section. A pull-up device is
included.
Power Resistor. Connect a resistor between this pin and VBAT. A 2.2 kΩ, 2 W
resistor should be used for a VBAT of –68.5 V. See the Applications section to
calculate resistor values for other VBAT potentials.
Protected Tip. The input to the tip fault protection and output of tip current
drive amplifier. Connect this pin to the tip of the loop through a 30 Ω overvolt-
age protection resistor.
Protected Ring. The input to the ring fault protection and output of ring cur-
rent drive amplifier. Connect this pin to the ring of the loop through a 30 Ω
overvoltage protection resistor.
Transmit ac Output Voltage. This output is a voltage that is directly propor-
tional to the differential tip/ring current.
Transmit Gain 2. Transmit gain and current limiting for ringing is set by the
value of RGX2. RGX2 is connected between TG2 and VITR.
Transmit Gain 1. Transmit gain is set by the series resistor combination of
RGX1 and RGX2 from this lead to TG2.
Ring Trip Filter. Connect this lead to RTTH via a resistor and to AGND with a
capacitor to filter the ring trip circuit to prevent spurious responses.
Ring Trip Threshold. Connect this lead to DCOUT via a resistor to set the ring
trip threshold.
dc Voltage Out. This output is a voltage that is directly proportional to the
absolute value of the differential tip/ring current.
Current-Limit Program Input. A resistor to DCOUT sets the dc current limit of
the circuit.
Receive Signal Input (+). This high-impedance input controls the ac differen-
tial voltage on tip/ring.
Receive Signal Input (–). This high-impedance input controls the ac differen-
tial voltage on tip/ring.
Analog Signal Ground.
Analog 5 V Power Supply.
Ringing Slope Resistor. Connect this lead to AGND with a resistor to set the
slope of the ringing waveform. Note that this pin is shared with both sections.
* On the printed-wiring board (PWB), make the leads to BGND and VBAT as wide as possible for thermal and electrical reasons. Also, maxi-
mize the amount of PWB copper on all leads connected to this device for the lowest operating temperature.
Note: Iu and Ou indicate a pull-up device is included on this lead.
6
Agere Systems Inc.
Share Link: 