LV4985VH 데이터 시트보기 (PDF) - SANYO -> Panasonic
부품명
상세내역
제조사
LV4985VH Datasheet PDF : 15 Pages
| |||
LV4985VH
4. pin 6 capacitor (C5)
This capacitor is a ripple filter capacitor. The internal resistors (600kΩ + 50kΩ) and C5 make up a low-pass filter that
is used to reduce the power supply ripple component and increase the ripple rejection ratio.
Note that inside the IC, the rising-transient-response-characteristic of the pin 6 voltage (reference voltage) is used to
activate the automatic pop noise reduction circuit. Therefore, when reducing the C5 capacitance value to increase the
voltage rise speed, the design should take into account that the pop noise increases during voltage rise.
5. Power supply line capacitor (C6 and C7)
The bypass capacitor C7 is used to remove the high frequency component that cannot be eliminated by the power
supply capacitor C6 (chemical capacitor). Place the bypass capacitor C7 as near to the IC as possible, and use a ceramic
capacitor with good high frequency characteristics.
When using a stabilized power supply, these capacitors can also be combined into a single 2.2μF ceramic capacitor.
Note that when the power supply line is relatively unstable, the power supply capacitor C6 capacitance value must be
increased.
6. Load capacitance
When connecting a capacitor between the output pin and ground to suppress electromagnetic radiation or other
purposes, the effects of this capacitor may cause the power amplifier phase margin to be reduced, resulting in
oscillation. When adding this capacitor, care should be taken for the capacitance value.
Recommended capacitance value : 1000pF to 0.1μF
7. Headphone drive
When also using the BTL amplifier’s first amplifier as the headphone amplifier, it is recommended to adjust the level
by inserting series resistors R9 (R10) to the signal line as shown in Application Circuit Example-2.
Note that this series resistor, the headphone load resistance and the output coupling capacitors C9 (C10) make up a
high-pass filter, so this should be taken into account in the design. The cut-off frequencies are expressed by the
following formulas.
1ch ⇒ fc5 = 1/ (2π × C9 × (R9 + RL))
2ch ⇒ fc6 = 1/ (2π × C10 × (R10 + RL))
8. Standby pin (pin 9)
As shown in Figure1, by controlling the standby pin, the mode changeover can be made between standby mode,
single-ended (SE) operating mode, and BTL operating mode.
State
Standby mode
Pin 9 voltage
0V to 0.3V
Port A
Low
Port B
Low
SE operating mode
1.3V to 1.7V
High
Low
BTL operating mode
2.3V to VCC
High
High
A-port
B-port
CPU
R5
STBY
9
R6
Fig. 1
LV4985VH
A-port
CPU
R5
Fig. 2
9 STBY
R5
VCC
9
STBY
VCC
3
Fig. 3
When not using the single-ended operating mode, a direct control is possible by connecting the standby pin to the CPU
output port. However, it is recommended to insert a series resistor R5 (1kΩ or more) as shown in Figure 2 in case the
pin is affected by the digital noise from CPU.
In addition, when not using the standby mode, the pin 9 can also be used interlocked with the power supply as shown in
Figure 3. Since there exists an internal current limiting resistor (30kΩ), the series resistor R5 can be eliminated, but the
current I9 expressed by the following formula flows through the pin 9, so this should be taken into account in the
design.
Pin 9 inflow current (unit : A) : I9 = 4.7 × 10-6 + (VCC - 0.7)/(R5 + 30000)
No.A1568-9/15
Share Link: 