MAX16936(2018) 데이터 시트보기 (PDF) - Maxim Integrated

부품명

상세내역

제조사

MAX16936
(Rev.:2018)

36V, 220kHz to 2.2MHz Step-Down Converters with 28µA Quiescent Current

Maxim Integrated 

MAX16936/MAX16938

36V, 220kHz to 2.2MHz Step-Down Converters

with 28µA Quiescent Current

one cycle. When the external clock signal at FSYNC is

absent for more than two clock cycles, the device reverts

back to the internal clock.

System Enable (EN)

An enable control input (EN) activates the device from its

low-power shutdown mode. EN is compatible with inputs

from automotive battery level down to 3.5V. The high

voltage compatibility allows EN to be connected to SUP,

KEY/KL30, or the inhibit pin (INH) of a CAN transceiver.

EN turns on the internal regulator. Once VBIAS is above

the internal lockout threshold, VUVL = 3.15V (typ), the

controller activates and the output voltage ramps up

within 8ms.

A logic-low at EN shuts down the device. During shut-

down, the internal linear regulator and gate drivers turn

off. Shutdown is the lowest power state and reduces the

quiescent current to 5FA (typ). Drive EN high to bring the

device out of shutdown.

Spread-Spectrum Option

The devices have an internal spread-spectrum option to

optimize EMI performance. This is factory set and the

S-version of the device should be ordered. For spread-

spectrum-enabled ICs, the operating frequency is

varied ±6% centered on FOSC. The modulation signal is

a triangular wave with a period of 110µs at 2.2MHz.

Therefore, FOSC will ramp down 6% and back to 2.2MHz in

110µs and also ramp up 6% and back to 2.2MHz in 110µs.

The cycle repeats.

For operations at FOSC values other than 2.2MHz, the

modulation signal scales proportionally, e.g., at 400kHz,

the 110µs modulation period increases to 110µs x

2.2MHz/400kHz = 605µs.

The internal spread spectrum is disabled if the device is

synced to an external clock. However, the device does not

filter the input clock and passes any modulation (including

spread-spectrum) present on the driving external clock to the

SYNCOUT pin.

Automatic Slew-Rate Control on LX

The devices have automatic slew-rate adjustment that

optimizes the rise times on the internal HSFET gate

drive to minimize EMI. The IC detects the internal clock

frequency and adjusts the slew rate accordingly. When

the user selects the external frequency setting resistor

RFOSC such that the frequency is > 1.1MHz, the HSFET

is turned on in 4ns (typ). When the frequency is < 1.1MHz

the HSFET is turned on in 8ns (typ). This slew-rate control

optimizes the rise time on LX node externally to minimize

EMI while maintaining good efficiency.

Internal Oscillator (FOSC)

The switching frequency (fSW) is set by a resistor

(RFOSC) connected from FOSC to AGND. See Figure 3

to select the correct RFOSC value for the desired switch-

ing frequency. For example, a 400kHz switching fre-

quency is set with RFOSC = 73.2kI. Higher frequencies

allow designs with lower inductor values and less output

capacitance. Consequently, peak currents and I2R losses

are lower at higher switching frequencies, but core losses,

gate charge currents, and switching losses increase.

Synchronizing Output (SYNCOUT)

SYNCOUT is an open-drain output that outputs a 180N

out-of-phase signal relative to the internal oscillator.

Overtemperature Protection

Thermal-overload protection limits the total power

dissipation in the devices. When the junction tempera-

ture exceeds 175NC (typ), an internal thermal sensor

shuts down the internal bias regulator and the step-down

controller, allowing the device to cool. The thermal

sensor turns on the device again after the junction

temperature cools by 15NC.

Applications Information

Setting the Output Voltage

Connect FB to BIAS for a fixed +5V/+3.3 output voltage.

To set the output to other voltages between 1V and 10V,

connect a resistive divider from output (OUT) to FB to

AGND (Figure 2). Use the following formula to determine

the RFB2 of the resistive divider network:

RFB2 = RTOTAL x VFB/VOUT

where VFB = 1V, RTOTAL = selected total resistance of

RFB1, RFB2 in ω, and VOUT is the desired output in volts.

MAX16936

MAX16938

FB

VOUT

RFB1

RFB2

Figure 2. Adjustable Output-Voltage Setting

www.maximintegrated.com

Maxim Integrated │  11

Share Link: