MAX2830 데이터 시트보기 (PDF) - Maxim Integrated
부품명
상세내역
제조사
MAX2830
Maxim Integrated
MAX2830 Datasheet PDF : 33 Pages
| |||
2.4GHz to 2.5GHz 802.11g/b RF Transceiver, PA,
and Rx/Tx/Antenna Diversity Switch
AC ELECTRICAL CHARACTERISTICS—Rx Mode (continued)
(MAX2830 EV kit, VCC_ = 2.8V, VCCPA = VCCTXPA = 3.3V, TA =+25°C, fRF = 2.439GHz, fLO = 2.437GHz; receiver baseband I/Q out-
puts at 112 mVRMS (-19dBV), fREF = 40MHz, SHDN = CS = high, RXTX = SCLK = DIN = low, with power matching for the differential
RF pins using the typical applications and registers set to default settings and corresponding test mode, unless otherwise noted.
Unmodulated single-tone RF input signal is used with specifications that normally apply over the entire operating conditions, unless
otherwise indicated. RF inputs/outputs specifications are referenced to device pins and do not include 1dB loss from EV kit PCB,
balun, and SMA connectors.) (Note 1)
PARAMETER
CONDITIONS
MIN TYP MAX UNITS
RF Gain Steps (Note 3)
From high-gain mode (B7:B6 = 11) to medium-gain
mode (B7:B6 = 10)
From high-gain mode (B7:B6 = 11) to low-gain mode
(B7:B6 = 0X)
-17
dB
-33.5
Gain change from high gain to medium gain, high gain to
RF Gain-Change Settling Time low, or medium gain to low gain; gain settling to within
0.2
µs
±2dB of steady state; RXHP = 1
Baseband Gain Range
DSB Noise Figure (ANT1)
DSB Noise Figure (ANT2)
In-Band Compression Point
Based on EVM
In-Band Output P-1dB
Out-of-Band Input IP3 (Note 4)
I/Q Phase Error
I/Q Gain Imbalance
RX I/Q Output Load Impedance
(R || C)
Tx-to-Rx Conversion Gain for Rx
I/Q Calibration
From maximum baseband gain (B5:B1 = 11111) to
minimum baseband gain (B5:B1 = 00000)
Voltage gain = maximum with B7:B6 = 11
Voltage gain = 50dB with B7:B6 = 11
Voltage gain = 45dB with B7:B6 = 10
Voltage gain = 15dB with B7:B6 = 0X
Voltage gain = maximum with B7:B6 = 11
Voltage gain = 50dB with B7:B6 = 11
Voltage gain = 45dB with B7:B6 = 10
Voltage gain = 15dB with B7:B6 = 0X
-19dBVRMS baseband
output EVM degrades to
9%
B7:B6 = 11
B7:B6 = 10
B7:B6 = 0X
Voltage gain = 90dB, with B7:B6 = 11
B7:B6 = 11
B7:B6 = 10
B7:B6 = 0X
1 σ variation (without calibration)
1 σ variation (without calibration)
Minimum differential resistance
Maximum differential capacitance
For receiver gain, B7:B1 = 1101111 (Note 5)
54
62
68
dB
3.3
3.8
16.7
34.7
4.0
4.5
17.4
35.3
-41
-24
-6
2.5
-12
-4
24
±0.35
±0.1
10
10
dB
dB
dBm
VP-P
dBm
Degrees
dB
kΩ
pF
0.5
dB
Baseband VGA Settling Time
Gain change from B5:B1 = 10111 to B5:B1 = 00111; gain
0.1
µs
settling to within ±2dB of steady state
I/Q Output DC Step when RXHP
Transitions from 1 to 0 in
Presence of 802.11g Short
Sequence
After switching RXHP to logic 0 from initial logic 1, during
ideal short sequence data at -55dBm input in AWGN
channel, for -19dBV output; normalized to RMS signal on
I and Q outputs; transition point varied from 0 to 0.8µs in
steps of 0.1µs
-5
dBc
4 _______________________________________________________________________________________
Share Link: